AT91SAM7L64-CU Atmel, AT91SAM7L64-CU Datasheet - Page 134

• Manufacturer Part Number: AT91SAM7L64-CU
• Description: MCU ARM7 64K HS FLASH 144-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7L64-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 36MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 1.55 V ~ 1.8 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 6 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM7L-STK - KIT EVAL FOR AT91SAM7LAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

18.3.3
18.3.4
134
AT91SAM7L128/64 Preliminary
Remap Command
Abort Status
Figure 18-4. Internal Memory Mapping with GPNVM Bit 0 = 1
After execution, the Remap Command causes the Internal SRAM to be accessed through the
Internal Memory Area 0.
As the ARM vectors (Reset, Abort, Data Abort, Prefetch Abort, Undefined Instruction, Interrupt,
and Fast Interrupt) are mapped from address 0x0 to address 0x20, the Remap Command allows
the user to redefine dynamically these vectors under software control.
The Remap Command is accessible through the Memory Controller User Interface by writing the
MC_RCR (Remap Control Register) RCB field to one.
The Remap Command can be cancelled by writing the MC_RCR RCB field to one, which acts as
a toggling command. This allows easy debug of the user-defined boot sequence by offering a
simple way to put the chip in the same configuration as after a reset.
There are two reasons for an abort to occur:
When an abort occurs, a signal is sent back to all the masters, regardless of which one has gen-
erated the access. However, only the ARM7TDMI can take an abort signal into account, and
only under the condition that it was generating an access. The Peripheral DMA Controller and
the EMAC do not handle the abort input signal. Note that the connections are not represented in
Figure
To facilitate debug or for fault analysis by an operating system, the Memory Controller integrates
an Abort Status register set.
The full 32-bit wide abort address is saved in MC_AASR. Parameters of the access are saved in
MC_ASR and include:
• access to an undefined address
• an access to a misaligned address.
• the size of the request (field ABTSZ)
• the type of the access, whether it is a data read or write, or a code fetch (field ABTTYP)
18-1.
256 Mbytes
0x0000 0000
0x0010 0000
0x0020 0000
0x0030 0000
0x0FFF FFFF
0x000F FFFF
0x001F FFFF
0x002F FFFF
0x003F FFFF
0x004F FFFF
0x0040 0000
0x0050 0000
Core SRAM (4 Kbytes) After Remap
Internal SRAM (Backup)
Internal SRAM (Core)
Flash Before Remap
Undefined Areas
Internal FLASH
Internal ROM
12 Kbytes
4 Kbytes
2 Kbytes
(Abort)
1 Mbyte
1 Mbyte
1 Mbyte
1 Mbyte
251 Mbytes
1 Mbyte
6257A–ATARM–20-Feb-08