STM32F101RBT6 STMicroelectronics, STM32F101RBT6 Datasheet - Page 53

• Manufacturer Part Number: STM32F101RBT6
• Description: MCU ARM 128KB FLASH/TIMER 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101RBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 3 x 16 bit
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6059

STM32F101x8, STM32F101xB
Table 33.
1. FT = 5V tolerant. To sustain a voltage higher than V
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
Symbol
V
R
R
C
V
V
I
PMOS/NMOS contribution
lkg
hys
PU
PD
IH
IO
IL
Standard I/O input low level
voltage
I/O FT
Standard I/O input high level
voltage
I/O FT
voltage
Standard IO Schmitt trigger
voltage hysteresis
IO FT Schmitt trigger voltage
hysteresis
Input leakage current
Weak pull-up equivalent
resistor
Weak pull-down equivalent
resistor
I/O pin capacitance
I/O static characteristics
All I/Os are CMOS and TTL compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters. The
coverage of these requirements is shown in
in
(1)
(1)
Figure 25
(5)
(5)
input low level voltage
input high level
Parameter
(2)
to the series resistance is minimum
and
(2)
(4)
Figure 26
V
for 5 V tolerant I/Os.
Standard I/Os
SS
Conditions
Doc ID 13586 Rev 13
V
V
V

I/O FT
IN
IN
IN
DD
V


= 5 V
IN
+0.5 the internal pull-up/pull-down resistors must be disabled.
V
V

DD
SS
(~10% order)
V
DD
0.41 (V
Figure 23
0.42 (V
5% V
.
–0.5
–0.5
Min
200
DD
30
30
DD
DD
–2)+1.3
–2)+1
(3)
and
Figure 24
Typ
40
40
5
Electrical characteristics
0.32 (V
0.28 (V
for standard I/Os, and
V
DD
Max
DD
DD
5.5
1
50
50
3
+0.5
–2)+0.75
–2)+0.8
53/85
Unit
mV
mV
µA
k
k
pF
V