Z16F2810FI20SG Zilog, Z16F2810FI20SG Datasheet - Page 116

• Manufacturer Part Number: Z16F2810FI20SG
• Description: IC ZNEO MCU FLASH 128K 80QFP
• Manufacturer: Zilog
• Series: Encore!® ZNEOr

Specifications of Z16F2810FI20SG

• Core Processor: ZNEO
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 80-BQFP
• Processor Series: Z16F2x
• Core: Zneo
• Data Bus Width: 16 bit
• Data Ram Size: 4 B
• Interface Type: ESPI, I2C, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: Z16F2800100ZCOG
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1003 - ISP 4PORT FOR ZILOG ZNEO MCU269-4537 - DEV KIT FOR Z16F ZNEO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4567

PS022008-0810
2. Write to the timer reload high and low byte registers to set the starting count value.
3. Write to the timer reload high and low byte registers to set the Reload value.
4. Enable the timer interrupt, if appropriate, and set the timer interrupt priority by writing
5. Configure the associated GPIO port pin for the timer input alternate function
6. When using the timer output function, configure the associated GPIO port pin for the
7. Write to the timer control 1 register to enable the timer.
PWM SINGLE and DUAL OUTPUT Modes
In PWM SINGLE OUTPUT mode, the timer outputs a PWM output signal through a
GPIO Port pin. In PWM DUAL OUTPUT mode, the timer outputs a PWM output signal
and also its complement through two GPIO port pins. The timer first counts up to the 
16-bit PWM match value stored in the timer PWM high and low byte registers. When the
timer count value matches the PWM value, the timer output toggles. The timer continues
counting until it reaches the Reload value stored in the timer reload high and low byte
registers. When it reaches the Reload value, the timer generates an interrupt. The count
value in the timer high and low byte registers is reset to
The timer output signal begins with value =
timer value matches the PWM value. The timer output signal returns to
timer reaches the Reload value and is reset to
In PWM DUAL OUTPUT mode, the timer also generates a second PWM output signal,
timer output complement (TOUT). A programmable deadband is configured (
to delay (0 to 128 system clock cycles) the Low to a High (inactive to active) output
transitions on these two pins. This configuration ensures a time gap between the
deassertion of one PWM output to the assertion of its complement.
Follow the steps below to configure a timer for PWM SINGLE or DUAL OUTPUT mode
and initiate the PWM operation:
1. Write to the timer control registers to:
This affects only the first pass in the COUNTER modes. After the first timer Reload,
counting always begins at the reset value of
to the relevant interrupt registers.
(COUNTER mode).
timer output alternate function.
–
–
–
–
–
Disable the timer.
Configure the timer for the selected PWM mode.
Set the prescale value.
Set the initial logic level (High or Low) and PWM High or Low transition for the
timer output alternate function with the TPOL bit.
Set the deadband delay (DUAL OUTPUT mode) with the
P R E L I M I N A R Y
TPOL
0001H
0001H
and then transits to
.
.
0001H
and counting resumes.
Product Specification
PWMD
ZNEO
TPOL
TPOL
field.
, when the
Z16F Series
PWMD
after the
Timers
field)
101