Z16F2810FI20SG Zilog, Z16F2810FI20SG Datasheet - Page 204

• Manufacturer Part Number: Z16F2810FI20SG
• Description: IC ZNEO MCU FLASH 128K 80QFP
• Manufacturer: Zilog
• Series: Encore!® ZNEOr

Specifications of Z16F2810FI20SG

• Core Processor: ZNEO
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 80-BQFP
• Processor Series: Z16F2x
• Core: Zneo
• Data Bus Width: 16 bit
• Data Ram Size: 4 B
• Interface Type: ESPI, I2C, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: Z16F2800100ZCOG
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1003 - ISP 4PORT FOR ZILOG ZNEO MCU269-4537 - DEV KIT FOR Z16F ZNEO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4567

PS022008-0810
Error Detection
From Master
From Master
From Master
Error events detected by the ESPI block are described in this section. Error events
generate an ESPI interrupt and set a bit in the ESPI status register. The error bits of the
ESPI Status register are read/write 1 to clear.
Transmit Underrun
A transmit underrun error occurs for a master with SSMD = 10 or 11 when a character
transfer completes and TDRE = 1. In these modes when a transmit underrun occurs the
transfer is aborted (SCK will halt and SSV will be deasserted). For a master in SPI mode
(
register to be written.
In SLAVE mode, a transmit underrun error occurs if TDRE = 1 at the start of a transfer.
When a transmit underrun occurs in SLAVE mode, ESPI transmits a character of all 1s.
A transmit underrun sets the TUND bit in the ESPI status register to 1. Writing 1 to TUND
clears this error flag.
Mode Fault (Multi-Master Collision)
A mode fault indicates when more than one master is trying to communicate at the same
time (a multi-master collision) in SPI mode. The mode fault is detected when the enabled
master’s SS input pin is asserted. For this to happen the control and mode registers must
be configured with MMEN = 1, SSIO = 0 (SS is an input) and SS input = 0. A mode fault
sets the COL bit in the ESPI status register to 1. Writing a 1 to COL clears this error flag.
SSMD = 00
To Master
) a transmit underrun is not signaled since SCK will pause and wait for the data
Figure 41. ESPI Configured as an SPI Slave
SS
MISO
MOSI
SCK
P R E L I M I N A R Y
Bit 7
8-bit Shift Register
SPI Slave
Bit 0
Enhanced Serial Peripheral Interface
Product Specification
ZNEO
Z16F Series
188