EP9315-CB Cirrus Logic Inc, EP9315-CB Datasheet - Page 773

• Manufacturer Part Number: EP9315-CB
• Description: IC ARM920T MCU 200MHZ 352-PBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-CB

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 352-BGA
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No
• Other names: 598-1261

DS785UM1
27.2.2 PIO Operations
For PIO operations, the Pin Interface unit handles all the operations. Register read and write
operations by the host are sufficient to operate the IDE interface in PIO mode for both non-
data and data transfer in both directions.
Most IDE controllers handle this automatically, but this IDE controller does not. The diagrams
are located in Information Technology AT Attachment with Packet Interface (ATA/ATAPI-5),
Section 10.2.2, Figure 44. See
additional information.
Initial state: pins DIORn and DIOWn low.
For a Read operation.
Note: NI = Not supported at this time.
1. Write out the register value.
2. Delay as follows, based on the PIO mode.
3. Bring DIORn high.
4. Based on the PIO mode, delay as follows before the next read or write can occur.
5. Bring DIORn low.
6. Read IDE Data in the register.
PIO Mode 0 - Delay for 70 ns
PIO Mode 1 - Delay for 50 ns.
PIO Mode 2 - Delay for 30 ns.
PIO Mode 3 - Delay for 30 ns
PIO Mode 4 - Delay for 25 ns
PIO Mode 0 - Delay for 290 ns.
PIO Mode 1 - Delay for 290 ns
PIO Mode 2 - Delay for 290 ns.
PIO Mode 3 - Delay for 80 ns
PIO Mode 4 - Delay for 70 ns
DDMARDYn/
DSTROBE
IOCS16n
IDE Pin
PDIAGn/
DD[15:0]
IORDY/
CBLIDn
Table 27-1. IDE Host to IDE Interface Definition (Continued)
Type
NI
NI
-
-
Copyright 2007 Cirrus Logic
No. of
"Preface"
Pins
16
1
1
1
Negate to extend the host transfer cycle of any host read or
write access/
Flow control signal for Ultra DMA data-out burst/
Flow control signal for Ultra DMA data-in burst
Device indicates it supports 16-bit I/O bus cycles
Asserted by device 1 to indicate to device 0 that it has finished
diagnostic/
Cable assembly type identifier
16-bit data interface between controller and device
chapter,
“Reference Documents” on page P-3
Description
EP93xx User’s Guide
IDE Interface
for
27-3
27