C8051F369-GM Silicon Laboratories Inc, C8051F369-GM Datasheet - Page 131

• Manufacturer Part Number: C8051F369-GM
• Description: IC 8051 MCU 16K FLASH 28-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F36xr

Specifications of C8051F369-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F360DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 21-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 21
• Height: 0.83 mm
• Length: 5 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1410 - KIT DEV FOR C8051F360 FAMILY
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1651

12.3. External Reset
The external RST pin provides a means for external circuitry to force the device into a reset state. Assert-
ing an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 12.1 for complete RST pin
specifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
12.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than 100 µs, the one-shot will time out and generate a reset. After a
MCD reset, the MCDRSF flag (RSTSRC.2) will read ‘1’, signifying the MCD as the reset source; otherwise,
this bit reads ‘0’. Writing a ‘1’ to the MCDRSF bit enables the Missing Clock Detector; writing a ‘0’ disables
it. The state of the RST pin is unaffected by this reset.
12.5. Comparator0 Reset
Comparator0 can be configured as a reset source by writing a ‘1’ to the C0RSEF flag (RSTSRC.5).
Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on
chatter on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-
inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the device is put into
the reset state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read ‘1’ signifying
Comparator0 as the reset source; otherwise, this bit reads ‘0’. The state of the RST pin is unaffected by
this reset.
Bit 7:
Bit 6:
Bits 5–0: RESERVED. Read = Variable. Write = don’t care.
SFR Page:
SFR Address:
VDMEN
R/W
Bit7
VDMEN: V
This bit turns the V
until it is also selected as a reset source in register RSTSRC (SFR Definition 12.2). The V
Monitor must be allowed to stabilize before it is selected as a reset source. Selecting the
V
0: V
1: V
V
This bit indicates the current power supply status (V
0: V
1: V
all pages
0xFF
DD
DD
VDDSTAT Reserved Reserved Reserved Reserved Reserved Reserved
DD
DD
DD
DD
Monitor as a reset source before it has stabilized may generate a system reset.
STAT: V
Bit6
R
Monitor Disabled.
Monitor Enabled.
is at or below the V
is above the V
SFR Definition 12.1. VDM0CN: V
DD
DD
Monitor Enable.
Status.
Bit5
R
DD
DD
Monitor circuit on/off. The V
Monitor threshold.
DD
Bit4
R
Monitor threshold.
C8051F360/1/2/3/4/5/6/7/8/9
Rev. 1.0
Bit3
R
DD
DD
Bit2
DD
R
Monitor cannot generate system resets
Monitor Control
Monitor output).
Bit1
R
Bit0
R
Reset Value
Variable
DD
131