MC9S12C32MFUE25 Freescale Semiconductor, MC9S12C32MFUE25 Datasheet - Page 198

• Manufacturer Part Number: MC9S12C32MFUE25
• Description: IC MCU 32K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C32MFUE25

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-QFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 8
• Operating Supply Voltage: 3.3 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: CML12C32SLK - KIT STUDENT LEARNING 16BIT HCS12
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 7 Debug Module (DBGV1) Block Description
1. The DBG module is designed for backwards compatibility to existing BKP modules. Register and bit names have changed from
2. Comparator C can be used to enhance the BKP mode by providing a third breakpoint.
7.3.2.1
198
Module Base + 0x0020
Starting address location affected by INITRG register setting.
the BKP module. This column shows the DBG register name, as well as the BKP register name for reference.
TRGSEL
DBGEN
Reset
BEGIN
Field
ARM
7
6
5
4
W
R
DBGEN
DBG Mode Enable Bit — The DBGEN bit enables the DBG module for use in DBG mode. This bit cannot be
set if the MCU is in secure mode.
0 DBG mode disabled
1 DBG mode enabled
Arm Bit — The ARM bit controls whether the debugger is comparing and storing data in the trace buffer. See
Section 7.4.2.4, “Arming the DBG
0 Debugger unarmed
1 Debugger armed
Note: This bit cannot be set if the DBGEN bit is not also being set at the same time. For example, a write of 01
Trigger Selection Bit — The TRGSEL bit controls the triggering condition for comparators A and B in DBG
mode. It serves essentially the same function as the TAGAB bit in the DBGC2 register does in BKP mode. See
Section 7.4.2.1.2, “Trigger
based on comparator A and B if enabled in DBG mode (DBGBRK = 1). Please refer to
“Breakpoint Based on Comparator A and
0 Trigger on any compare address match
1 Trigger before opcode at compare address gets executed (tagged-type)
Begin/End Trigger Bit — The BEGIN bit controls whether the trigger begins or ends storing of data in the trace
buffer. See
more details.
0 Trigger at end of stored data
1 Trigger before storing data
Debug Control Register 1 (DBGC1)
0
7
All bits are used in DBG mode only.
This register cannot be written if BKP mode is enabled (BKABEN in
DBGC2 is set).
to DBGEN[7:6] will be interpreted as a write of 00.
= Unimplemented or Reserved
Section 7.4.2.8.1, “Storing with
ARM
0
6
Figure 7-4. Debug Control Register (DBGC1)
Table 7-3. DBGC1 Field Descriptions
Selection,” for more information. TRGSEL may also determine the type of breakpoint
TRGSEL
MC9S12C-Family / MC9S12GC-Family
0
5
Module,” for more information.
B.”
BEGIN
Begin-Trigger,” and
Rev 01.24
NOTE
NOTE
0
4
Description
DBGBRK
0
3
Section 7.4.2.8.2, “Storing with
0
0
2
Freescale Semiconductor
Section 7.4.3.1,
0
1
CAPMOD
End-Trigger,” for
0
0