ATTINY25-20SH Atmel, ATTINY25-20SH Datasheet - Page 218

• Manufacturer Part Number: ATTINY25-20SH
• Description: IC MCU AVR 2KB FLASH 20MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25-20SH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Processor Series: ATtiny
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.2
27.2.1
27.2.2
27.2.3
218
Errata ATtiny45
ATtiny25/45/85
Rev F and G
Rev D and E
Rev B and C
The revision letter in this section refers to the revision of the ATtiny45 device.
No known errata
•
1. EEPROM read may fail at low supply voltage / low clock frequency
•
•
•
•
1. PLL not locking
2. EEPROM read from application code does not work in Lock Bit Mode 3
3. EEPROM read may fail at low supply voltage / low clock frequency
EEPROM read may fail at low supply voltage / low clock frequency
PLL not locking
EEPROM read from application code does not work in Lock Bit Mode 3
EEPROM read may fail at low supply voltage / low clock frequency
Timer Counter 1 PWM output generation on OC1B- XOC1B does not work correctly
Trying to read EEPROM at low clock frequencies and/or low supply voltage may result in
invalid data.
Problem Fix/Workaround
Do not use the EEPROM when clock frequency is below 1 MHz and supply voltage is below
2V. If operating frequency can not be raised above 1 MHz then supply voltage should be
more than 3V. Similarly, if supply voltage can not be raised above 2V then operating fre-
quency should be more than 2 MHz.
This feature is known to be temperature dependent but it has not been characterised.
Guidelines are given for room temperature, only.
When at frequencies below 6.0 MHz, the PLL will not lock
Problem fix / Workaround
When using the PLL, run at 6.0 MHz or higher.
When the Memory Lock Bits LB2 and LB1 are programmed to mode 3, EEPROM read does
not work from the application code.
Problem Fix/Work around
Do not set Lock Bit Protection Mode 3 when the application code needs to read from
EEPROM.
Trying to read EEPROM at low clock frequencies and/or low supply voltage may result in
invalid data.
Problem Fix/Workaround
Do not use the EEPROM when clock frequency is below 1 MHz and supply voltage is below
2V. If operating frequency can not be raised above 1 MHz then supply voltage should be
2586M–AVR–07/10