AT91SAM7X128B-AU Atmel, AT91SAM7X128B-AU Datasheet - Page 288

• Manufacturer Part Number: AT91SAM7X128B-AU
• Description: IC MCU 128KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: JTAG, SPI, UART
• Maximum Clock Frequency: 55 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

29.5.6
288
SAM7X512/256/128 Preliminary
Read/Write Flowcharts
The following flowcharts shown in
page
give examples for read and write operations. A polling or interrupt method can be used to check
the status bits. The interrupt method requires that the interrupt enable register (TWI_IER) be
configured first.
Figure 29-13. TWI Write Operation with Single Data Byte without Internal Address
290,
Figure 29-16 on page
(CLDIV, CHDIV, CKDIV) in TWI_CWGR
- Device slave address (DADR)
Set the Master Mode register:
291,
Write ==> bit MREAD = 0
TWI_THR = Data to send
Set the Control register:
Load Transmit register
- Transfer direction bit
Read Status register
Read Status register
Figure
(Needed only once)
TWI_CR = MSEN
Transfer finished
- Master enable
TXCOMP = 1?
Set TWI clock
Figure 29-17 on page 292
TXRDY = 1?
Yes
Yes
BEGIN
29-13,
Figure 29-14 on page
No
No
and
Figure 29-18 on page 293
289,
6120I–ATARM–06-Apr-11
Figure 29-15 on