P89LPC9408FBD,557 NXP Semiconductors, P89LPC9408FBD,557 Datasheet - Page 43

• Manufacturer Part Number: P89LPC9408FBD,557
• Description: IC 80C51 MCU FLASH 8K 64-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC9408FBD,557

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 64-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LED, POR, PWM, WDT
• Number Of I /o: 23
• Eeprom Size: 512 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC9x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: OM10097 - KIT FOR LCD DEMO LPC9408EPM900K - EMULATOR/PROGRAMMER NXP P89LPC9568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART568-1759 - EMULATOR DEBUGGER/PROGRMMR LPC9X
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-3228; 935280583557; P89LPC9408FBD

Philips Semiconductors
P89LPC9408_1
Product data sheet
Fig 20. Watchdog timer in Watchdog mode (WDTE = 1)
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a
feed sequence.
watchdog
oscillator
MOV WFEED1, #0A5H
MOV WFEED2, #05AH
PCLK
7.26.1 Software reset
7.26.2 Dual data pointers
7.27.1 General description
7.26 Additional features
7.27 LCD controller
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the address
used with certain instructions. The DPS bit in the AUXR1 register selects one of the two
Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS bit may
be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1 register,
without the possibility of inadvertently altering other bits in the register.
The LCD segment driver in the P89LPC9408 can interface to most LCDs using low
multiplex rates. It generates the drive signals for static or multiplexed LCDs containing up
to four backplanes and up to 32 segments. The LCD controller communicates to a host
using the I
LCD controller are available on the P89LPC9408 providing system flexibility.
Communication overhead to manage the display is minimized by an on-chip display RAM
with auto-increment addressing, hardware subaddressing, and display memory switching
(static and duplex drive modes).
WDCON (A7H)
32
2
C-bus. The I
8-bit two-clock 80C51 core with 32 segment
PRE2
PRESCALER
Rev. 01 — 16 December 2005
PRE1
2
C-bus clock and data signals for both the microcontroller and the
PRE0
SHADOW REGISTER
-
-
8-BIT DOWN
WDL (C1H)
COUNTER
WDRUN
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
WDTOF
P89LPC9408
4 LCD driver, 10-bit ADC
WDCLK
002aaa905
reset
(1)
43 of 69