ST7FMC1K2T6 STMicroelectronics, ST7FMC1K2T6 Datasheet - Page 238

• Manufacturer Part Number: ST7FMC1K2T6
• Description: MCU 8BIT 8K FLASH 32-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FMC1K2T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI
• Peripherals: LVD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST7FMC1x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 1
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MC-KIT/BLDC, ST7MDT50-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-8402 - BOARD EVAL COMPLETE INVERTER497-8400 - KIT IGBT PWR MODULE CTRL ST7MC497-4734 - EVAL KIT 3KW POWER DRIVER BOARD497-4733 - EVAL KIT 1KW POWER DRIVER BOARD497-4732 - EVAL KIT 300W POWER DRIVER BOARD497-4731 - EVAL KIT PWR DRIVER CONTROL BRD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-4865

ST7MC1xx/ST7MC2xx
10-BIT A/D CONVERTER (ADC) (Cont’d)
When a conversion is complete:
To read the 10 bits, perform the following steps:
1. Poll the EOC bit or wait for EOC interrupt
2. Read ADCDRLSB
3. Read ADCDRMSB
The EOC bit is reset by hardware once the AD-
CDRMSB is read.
To read only 8 bits, perform the following steps:
1. Poll the EOC bit or wait for EOC interrupt
2. Read ADCDRMSB
The EOC bit is reset by hardware once the AD-
CDRMSB is read.
Changing the conversion channel
The application can change channels during con-
version. In this case the current conversion is
stopped and the A/D converter starts converting
the newly selected channel.
ADCCR consistency
If an End Of Conversion event occurs after soft-
ware has read the ADCDRLSB but before it has
read the ADCDRMSB, there would be a risk that
the two values read would belong to different sam-
ples.
238/309
– The EOC bit is set by hardware
– An interrupt request is generated if the ADCIE
– The result is in the ADCDR registers and re-
bit in the MCCBCR register is set (see
6.4.7 on page
mains valid until the next conversion has end-
ed.
38).
section
To guarantee consistency:
Thus, it is mandatory to read the ADCDRMSB just
after reading the ADCDRLSB. Otherwise the AD-
CDR register will not be updated until the AD-
CDRMSB is read.
10.8.4 Low Power Modes
Note: The A/D converter may be disabled by re-
setting the ADON bit. This feature allows reduced
power consumption when no conversion is need-
ed.
10.8.5 Interrupts
1)
section 6.4.7 on page
Mode
Wait
Halt
End of Conver-
sion
The ADCIE bit is in the MCCBCR register (see
– The ADCDRMSB and the ADCDRLSB are
– The ADCDRMSB and the ADCDRLSB are un-
Interrupt
locked when the ADCCRLSB is read
locked when the MSB is read or when ADON
is reset.
Event
Description
No effect on A/D Converter
A/D Converter disabled.
After wake up from Halt mode, the A/D
Converter requires a stabilization time
t
before accurate conversions can be
performed.
STAB
Event
EOC
Flag
(see Electrical Characteristics)
38)
ADCIE
Control
Enable
Bit
1)
from
Wait
Exit
Yes
from
Exit
Halt
No