Z8F4822AR020SG Zilog, Z8F4822AR020SG Datasheet - Page 137

• Manufacturer Part Number: Z8F4822AR020SG
• Description: IC ENCORE MCU FLASH 48K 64LQFP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F4822AR020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-LQFP
• Processor Series: Z8F482x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 46
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4271; Z8F4822AR020SG

PS019921-0308
Baud Rate
IR_RXD
UART’s
Clock
RXD
Caution:
8-clock
delay
Start Bit = 0
When the Infrared Endec is enabled, the UART’s RXD signal is internal to the Z8 Encore!
XP
Endec Receiver Synchronization
The IrDA receiver uses a local baud rate clock counter (0 to 15 clock periods) to generate
an input stream for the UART and to create a sampling window for detection of incoming
pulses. The generated UART input (UART RXD) is delayed by 8 baud rate clock periods
with respect to the incoming IrDA data stream. When a falling edge in the input data
stream is detected, the Endec counter is reset. When the count reaches a value of 8, the
UART RXD value is updated to reflect the value of the decoded data. When the count
reaches 12 baud clock periods, the sampling window for the next incoming pulse opens.
The window remains open until the count again reaches 8 (or in other words 24 baud clock
periods since the previous pulse was detected). This gives the Endec a sampling window
of minus four baudrate clocks to plus eight baudrate clocks around the expected time of an
incoming pulse. If an incoming pulse is detected inside this window this process is
repeated. If the incoming data is a logical 1 (no pulse), the Endec returns to the initial state
and waits for the next falling edge. As each falling edge is detected, the Endec clock
counter is reset, resynchronizing the Endec to the incoming signal. This action allows the
Endec to tolerate jitter and baud rate errors in the incoming data stream. Resynchronizing
the Endec does not alter the operation of the UART, which ultimately receives the data.
The UART is only synchronized to the incoming data stream when a Start bit is received.
16-clock
min. 1.6
period
®
The system clock frequency must be at least 1.0 MHz to ensure proper recep-
tion of the 1.6
pulse
F64XX Series products while the IR_RXD signal is received through the
Start Bit = 0
µ
16-clock
s
period
Data Bit 0 = 1
Figure 20. Infrared Data Reception
µ
s minimum width pulses allowed by the IrDA standard.
Data Bit 0 = 1
16-clock
period
Data Bit 1 = 0
Data Bit 1 = 0
16-clock
period
Data Bit 2 = 1
Z8 Encore! XP
Data Bit 2 = 1
16-clock
period
Product Specification
Infrared Encoder/Decoder
Data Bit 3 = 1
®
F64XX Series
Data Bit 3 = 1
RXD
pin.
123