STM32F103RCT6TR STMicroelectronics, STM32F103RCT6TR Datasheet - Page 82

• Manufacturer Part Number: STM32F103RCT6TR
• Description: MCU ARM 32BIT 256KB FLASH 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103RCT6TR

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Core: ARM Cortex M3
• Processor Series: STM32F103x
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 72 MHz
• Data Ram Size: 48 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 51
• Number Of Timers: 8
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 16
• Height: 1.4 mm
• Interface Type: CAN, I2C, SPI, USART
• Length: 10 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2 V
• Width: 10 mm
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Electrical characteristics
5.3.13
Table 45.
1. FT = Five-volt tolerant.
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
82/123
Symbol
V
R
R
C
V
V
V
V
I
MOS/NMOS contribution
lkg
hys
PU
PD
IH
IH
IO
IL
IL
Input low level voltage
Standard IO input high level voltage
IO FT
Input low level voltage
Input high level voltage
Standard IO Schmitt trigger voltage
hysteresis
IO FT Schmitt trigger voltage
hysteresis
Input leakage current
Weak pull-up equivalent resistor
Weak pull-down equivalent resistor
I/O pin capacitance
Static latch-up
Two complementary static tests are required on six parts to assess the latch-up
performance:
●
●
These tests are compliant with EIA/JESD 78A IC latch-up standard.
Table 44.
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in
performed under the conditions summarized in
compliant.
I/O static characteristics
Symbol
(1)
LU
input high level voltage
A supply overvoltage is applied to each power supply pin
A current injection is applied to each input, output and configurable I/O pin
(2)
(2)
Parameter
to the series resistance is minimum
Static latch-up class
Electrical sensitivities
(4)
Parameter
(5)
(5)
Doc ID 14611 Rev 7
V
V
T
Standard I/Os
CMOS ports
SS
A
IN
Conditions
(~10% order)
TTL ports
V
V
+105 °C conforming to JESD78A
= 5 V,

IN
IN
V


IN
V
V
I/O FT

DD
STM32F103xC, STM32F103xD, STM32F103xE
SS
V
DD
.
Table
Conditions
5% V
Table 45
0.65 V
10. All I/Os are CMOS and TTL
–0.5
–0.5
Min
200
30
30
2
2
DD
DD
(3)
are derived from tests
Typ
40
40
5
0.35 V
V
V
DD
DD
5.5V
Max
0.8
1
50
50
3
+0.5
+0.5
DD
II level A
Class
Unit
mV
mV
µA
k
k
pF
V
V