ST10R272LT6 STMicroelectronics, ST10R272LT6 Datasheet - Page 41

• Manufacturer Part Number: ST10R272LT6
• Description: IC MCU 16BIT LV ROMLESS 100-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10R272LT6

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-TQFP, 144-VQFP
• Processor Series: ST10R2x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: SSP, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 77
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-2045

Remarks on 5 volt tolerant (5T) and 5 volt fail-safe (5S) pins
The 5V tolerant input and output pins can sustain an absolute maximum external voltage of
5.5V.
However, signals on unterminated bus lines might have overshoot above 5.5V, presenting
latchup and hot carrier risks. While these risks are under evaluation, observe the following se-
curity recommendations:
•
•
Power supply failure condition
The power supply failure condition is a state where the chip is NOT supplied but is connected
to active signal lines. There are several cases:
•
•
•
•
•
•
•
Maximum peak voltage on 5V tolerant pin with respect to ground ( V
If the ringing of the external signal exceeds 6V, then clip the signal to the 5V supply.
3.3V external lines on 3.3V (3T) pin on the non powered chip: ...............NOT Acceptable
3.3V external lines on 5V tolerant (5T) pin on the non powered chip: ............. Acceptable
The 5V tolerant buffer do not leak: external signals not altered. No reliability problem.
3.3V external lines on 5V fail-safe (5S) pin on the non powered chip: ............ Acceptable
The 5V tolerant buffer do not leak: external signals not altered. No reliability problem.
5.5V external lines on 5V tolerant (5T) pin on the non powered chip: ............. Acceptable
For VERY SHORT times only: the buffers do not leak (external signals not altered) but
there is a fast degradation of the gate oxides in the buffers. The total maximum time under
this stress condition is 2 days. This limits this configuration to short power-up/down
sequences. For 10 year life time, the maximum duty factor is 1/1800 allowing e.g. a
maximum stress duration of 48 seconds per day.
5.5V external lines on 5V fail-safe (5S) pin on the non powered chip: ............ Acceptable
6V transient signals on 5V tolerant (5T) pin on the non powered chip: ...NOT Acceptable
6V transient signals on 5V fail-safe (5S) pin on the non powered chip:.......... Acceptable
ST10R272L - ELECTRICAL CHARACTERISTICS
SS
)= +6 V
41/77
1