MC9S08SH8CTG Freescale Semiconductor, MC9S08SH8CTG Datasheet - Page 280

• Manufacturer Part Number: MC9S08SH8CTG
• Description: IC MCU 8BIT 8K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH8CTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 13
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO9S08SH8 - BOARD DEMO FOR MC9S08SH FAM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Chapter 17 Development Support
A-Only — Trigger when the address matches the value in comparator A
A OR B — Trigger when the address matches either the value in comparator A or the value in
comparator B
A Then B — Trigger when the address matches the value in comparator B but only after the address for
another cycle matched the value in comparator A. There can be any number of cycles after the A match
and before the B match.
A AND B Data (Full Mode) — This is called a full mode because address, data, and R/W (optionally)
must match within the same bus cycle to cause a trigger event. Comparator A checks address, the low byte
of comparator B checks data, and R/W is checked against RWA if RWAEN = 1. The high-order half of
comparator B is not used.
In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you
do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the
CPU breakpoint is issued when the comparator A address matches.
A AND NOT B Data (Full Mode) — Address must match comparator A, data must not match the low
half of comparator B, and R/W must match RWA if RWAEN = 1. All three conditions must be met within
the same bus cycle to cause a trigger.
In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you
do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the
CPU breakpoint is issued when the comparator A address matches.
Event-Only B (Store Data) — Trigger events occur each time the address matches the value in
comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the
FIFO becomes full.
A Then Event-Only B (Store Data) — After the address has matched the value in comparator A, a trigger
event occurs each time the address matches the value in comparator B. Trigger events cause the data to be
captured into the FIFO. The debug run ends when the FIFO becomes full.
Inside Range (A ≤ Address ≤ B) — A trigger occurs when the address is greater than or equal to the value
in comparator A and less than or equal to the value in comparator B at the same time.
Outside Range (Address < A or Address > B) — A trigger occurs when the address is either less than
the value in comparator A or greater than the value in comparator B.
MC9S08SH8 MCU Series Data Sheet, Rev. 3
280
Freescale Semiconductor