MCHC908GR8CFAE Freescale Semiconductor, MCHC908GR8CFAE Datasheet - Page 104

• Manufacturer Part Number: MCHC908GR8CFAE
• Description: IC MCU FLSH 8BIT8MHZ 7.5K32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

External Interrupt (IRQ)
The vector fetch or software clear and the return of the IRQ pin to logic 1 may occur in any order. The
interrupt request remains pending as long as the IRQ pin is at logic 0. A reset will clear the latch and the
MODE control bit, thereby clearing the interrupt even if the pin stays low.
If the MODE bit is clear, the IRQ pin is falling-edge-sensitive only. With MODE clear, a vector fetch or
software clear immediately clears the IRQ latch.
The IRQF bit in the INTSCR register can be used to check for pending interrupts. The IRQF bit is not
affected by the IMASK bit, which makes it useful in applications where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ pin.
8.5 IRQ Module During Break Interrupts
The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear the latch during
the break state. See
To allow software to clear the IRQ latch during a break interrupt, write a 1 to the BCFE bit. If a latch is
cleared during the break state, it remains cleared when the MCU exits the break state.
To protect CPU interrupt flags during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default
state), writing to the ACK bit in the IRQ status and control register during the break state has no effect on
the IRQ interrupt flags.
8.6 IRQ Status and Control Register
The IRQ status and control register (INTSCR) controls and monitors operation of the IRQ module. The
INTSCR:
104
•
•
•
•
•
IRQ pin and require software to clear the IRQ latch. Writing to the ACK bit prior to leaving an
interrupt service routine can also prevent spurious interrupts due to noise. Setting ACK does not
affect subsequent transitions on the IRQ pin. A falling edge that occurs after writing to the ACK bit
another interrupt request. If the IRQ mask bit, IMASK, is clear, the CPU loads the program counter
with the vector address at locations $FFFA and $FFFB.
Return of the IRQ pin to logic 1 — As long as the IRQ pin is at logic 0, IRQ remains active.
Shows the state of the IRQ flag
Clears the IRQ latch
Masks IRQ interrupt request
Controls triggering sensitivity of the IRQ interrupt pin
Address:
When using the level-sensitive interrupt trigger, avoid false interrupts by
masking interrupt requests in the interrupt routine.
Reset:
Read:
Write:
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Chapter 19 Development
$001D
Figure 8-4. IRQ Status and Control Register (INTSCR)
Bit 7
0
= Unimplemented
6
0
5
0
Support.
NOTE
4
0
IRQF
3
0
ACK
2
0
0
IMASK
1
0
Freescale Semiconductor
MODE
Bit 0
0