TS1871AIYLT STMicroelectronics, TS1871AIYLT Datasheet - Page 3

• Manufacturer Part Number: TS1871AIYLT
• Description: IC OP AMP RRIO 1.8V LP SOT-23-5
• Manufacturer: STMicroelectronics

Specifications of TS1871AIYLT

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 0.6 V/µs
• Gain Bandwidth Product: 1.8MHz
• Current - Input Bias: 70nA
• Voltage - Input Offset: 100µV
• Current - Supply: 500µA
• Current - Output / Channel: 80mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Other names: 497-10234-2

TS187x, TS187xA
1
Absolute maximum ratings and operating conditions
Table 2.
1. All voltage values, except differential voltages, are with respect to network terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If
3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-
4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
6. Charged device model: all pins and package are charged together to the specified voltage and then
7. Short-circuits from the output to V
Symbol
V
resistor to limit the input current.
circuits on all amplifiers.
1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
discharged directly to ground through only one pin. This is done for all pins.
approximately 80 mA, independent of the magnitude of V
simultaneous short-circuits on all amplifiers.
R
ESD
R
V
T
id
V
V
T
CC
thja
thjc
stg
> ±1 V, the maximum input current must not exceed ±1 mA. When V
id
in
j
Absolute maximum ratings
Supply voltage
Differential input voltage
Input voltage
Storage temperature
Maximum junction temperature
Thermal resistance junction to ambient
Thermal resistance junction to case
HBM: human body model
MM: machine model
CDM: charged device model
Latch-up immunity
Lead temperature (soldering, 10 sec)
Output short-circuit duration
SOT23-5
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
SOT23-5
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
(1)
Parameter
CC
Doc ID 6992 Rev 5
(5)
can cause excessive heating. The maximum output current is
(2)
Absolute maximum ratings and operating conditions
(4)
(6)
(3)
CC
. Destructive dissipation can result from
V
CC-
id
> ±1 V, add an input series
-0.3 to V
-65 to +150
see note
Value
150
250
190
125
103
120
100
200
200
250
1.5
±1
81
39
40
31
37
32
7
2
CC+
(7)
+0.3
°C/W
°C/W
Unit
mA
°C
°C
kV
kV
°C
V
V
V
V
3/25