AT86RF231-ZUR Atmel, AT86RF231-ZUR Datasheet - Page 75

• Manufacturer Part Number: AT86RF231-ZUR
• Description: IC RADIO TXRX 2.4GHZ 32-VQFN
• Manufacturer: Atmel

Specifications of AT86RF231-ZUR

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Applications: Industrial Monitoring and Control, Wireless Alarm and Security Systems
• Power - Output: -17dBm ~ 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.3mA
• Current - Transmitting: 14mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 2405 MHz to 2480 MHz
• Interface Type: SPI
• Noise Figure: 6 dB
• Output Power: 20 dB
• Operating Supply Voltage: 2.5 V, 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 12.3 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8111C–MCU Wireless–09/09
Bit
+0x2F
Read/Write
Reset Value
R/W
7
0
AACK_SET_PD is also copied into the frame pending subfield of the acknowledgment frame for
any MAC command frame with a frame version of 2 or 3 that have the security enabled subfield
set to 1. This is done in the assumption that a future version of the standard
length or structure of the auxiliary security header, so it is not possible to safely detect whether
the MAC command frame is actually a data request command or not.
• Bit 4 - AACK_ DIS_ACK
If this bit is set no acknowledgment frames are transmitted in RX_AACK Extended Operating
Mode, even if requested.
• Bit 3 - AACK_I_AM_COORD
This register bit has to be set if the node is a PAN coordinator. It is used for address filtering in
RX_AACK.
If AACK_I_AM_COORD = 1 and if only source addressing fields are included in a data or MAC
command frame, the frame shall be accepted only if the device is the PAN coordinator and the
source PAN identifier matches macPANId, for details refer to IEEE 802.15.4, section 7.5.6.2
(third-level filter rule 6).
• Bit [2:0] - CSMA_SEED_1
These register bits are the higher 3-bit of the CSMA_SEED, bits [10:8]. The lower part is in reg-
ister 0x2D (CSMA_SEED_0), see register CSMA_SEED_0 for details.
Register 0x2F (CSMA_BE):
• Bit [7:4] - MAX_BE
Register bits MAX_BE defines the maximum back-off exponent used in the CSMA-CA algorithm
to generate a pseudo random number for back off the CCA. For details refer to IEEE 802.15.4-
2006, Section 7.5.1.4.
Valid values are [4'd8, 4'd7, … , 4'd3].
• Bit [3:0] - MIN_BE
Register bits MIN_BE defines the minimum back-off exponent used in the CSMA-CA algorithm
to generate a pseudo random number for back off the CCA. For details refer to IEEE 802.15.4-
2006, Section 7.5.1.4.
Valid values are [MAX_BE, (MAX_BE - 1), … , 4'd0].
Note
R/W
6
• If MIN_BE = 0 and MAX_BE = 0 the CCA back off period is always set to 0.
1
MAX_BE
R/W
5
0
R/W
4
1
R/W
3
0
R/W
2
0
MIN_BE
R/W
1
1
AT86RF231
[1]
R/W
0
1
might change the
CSMA_BE
75