XC2V8000-4FF1517I Xilinx Inc, XC2V8000-4FF1517I Datasheet - Page 51

• Manufacturer Part Number: XC2V8000-4FF1517I
• Description: IC FPGA VIRTEX-II 1517FCBGA
• Manufacturer: Xilinx Inc
• Series: Virtex™-IIr

Specifications of XC2V8000-4FF1517I

• Number Of Labs/clbs: 11648
• Total Ram Bits: 3096576
• Number Of I /o: 1108
• Number Of Gates: 8000000
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1517-BBGA, FCBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Logic Elements/cells: -

Table 4: Quiescent Supply Current
Power-On Power Supply Requirements
Xilinx FPGAs require a certain amount of supply current
during power-on to insure proper device operation. The
actual current consumed depends on the power-on ramp
rate of the power supply.
The V
ramp on, monotonically, no faster than 200 μs and no slower
than 50 ms. Ramp on is defined as: 0 V
ply voltages.
Table 5
devices for proper power on and configuration.
Power supplies can be turned on in any sequence.
DS031-3 (v3.5) November 5, 2007
Product Specification
Notes:
1. With no output current loads, no active input pull-up resistors, all I/O pins are 3-state and floating.
2. If DCI or differential signaling is used, more accurate values can be obtained by using the Power Estimator or XPOWER™.
3. Data are retained even if V
4. Values specified for quiescent supply current parameters are Commercial Grade. For Industrial Grade values, multiply Commercial
I
Symbol
I
CCAUXQ
CCINTQ
I
CCOQ
Grade values by 1.25.
CCINT
shows the minimum current required by Virtex-II
, V
R
Quiescent V
Quiescent V
Quiescent V
CCAUX
, and V
CCINT
CCO
CCAUX
Description
CCO
CCO
supply current
supply current
supply current
drops to 0 V.
power supplies shall each
DC
to minimum sup-
(1,2)
(1,2)
(1)
www.xilinx.com
Virtex-II Platform FPGAs: DC and Switching Characteristics
XC2V1000
XC2V1500
XC2V2000
XC2V3000
XC2V4000
XC2V6000
XC2V8000
XC2V1000
XC2V1500
XC2V2000
XC2V3000
XC2V4000
XC2V6000
XC2V8000
XC2V1000
XC2V1500
XC2V2000
XC2V3000
XC2V4000
XC2V6000
XC2V8000
XC2V250
XC2V500
XC2V250
XC2V500
XC2V250
XC2V500
XC2V40
XC2V80
XC2V40
XC2V80
XC2V40
XC2V80
Device
If any V
draws up to 300 mA, worst case, until the V
up.
to the minimum value above, or larger, the device powers on
properly after all three supplies have passed through their
power-on reset threshold voltages.
Once initialized and configured, use the power calculator to
estimate current drain on these supplies.
Notes:
1. If the V
2. The 300 mA is transient current (peak); it eventually
(2)
be applied before V
damaged if this requirement is violated, but configuration will
probably fail.
disappears even if V
This does not harm the device. If the current is limited
CCO
CCINT
bank powers up before V
Min
ramp rate is longer than 10 ms, then V
CCO
CCAUX
and V
Typical
12.5
12.5
7.5
7.5
does not power up.
10
12
15
20
27
35
45
60
10
10
3
5
8
1
1
1
1
1
2
2
2
2
2
2
5
5
5
5
5
CCAUX
CCAUX
. The device will not be
1100
Max
125
125
150
200
250
350
400
500
650
800
100
100
25
25
25
25
25
50
50
75
75
2
2
2
2
2
4
4
4
4
4
4
, then each bank
CCAUX
Module 3 of 4
CCINT
Units
powers
mA
mA
mA
must
3