PI7C21P100BNHE Pericom Semiconductor, PI7C21P100BNHE Datasheet - Page 14

• Manufacturer Part Number: PI7C21P100BNHE
• Description: Peripheral Drivers & Components (PCIs) PCI-X to PCI-XBridge 2 Port
• Manufacturer: Pericom Semiconductor

Specifications of PI7C21P100BNHE

• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3 V to 3.6 V
• Package / Case: CSBGA-304
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.2.4
SECONDARY BUS INTERFACE SIGNALS – 64-BIT EXTENSION
Name
S_PERR#
S_SERR#
S_REQ[6:2]#
S_REQ[1]#
S_GNT[6:2]#
S_GNT[1]#
S_RST#
Name
S_AD[63:32]
Pin #
AB17
AB19
AC3, AB5, AB3,
W2, AA2
AA23
AC4, AB4, AC5, Y2,
AB1
AA19
U23
Pin #
AB8, AB7, AA7,
AB6, AA6, AA5, Y6,
Y3, V2, V4, U2, U3,
T2, T3, R2, R3, P2,
Y1, P3, W1, P4, U1,
N2, N3, M2, M3, R1,
L2, L3, K2, K3, K4
Page 14 of 79
Type
Type
STS
TS
TS
TS
O
I
I
I
Description
Secondary Parity Error (Active LOW): Asserted
when a data parity error is detected for data received on
the secondary interface. Before being tri-stated, it is
driven HIGH for one cycle.
Secondary System Error (Active LOW): Can be
driven LOW by any device to indicate a system error
condition.
Secondary Request (Active LOW): This is asserted by
an external device to indicate that it wants to start a
transaction on the secondary bus. The input is externally
pulled up through a resistor to VDD.
Secondary Request (Active LOW):
When the internal arbiter is enabled, this is asserted by
an external device to indicate that it wants to start a
transaction on the secondary bus. The input is externally
pulled up through a resistor to VDD.
When the internal arbiter is disabled, this is used by
PI7C21P100B as its GNT input.
Secondary Grant (Active LOW): PI7C21P100B
asserts these pins to allow external masters to access the
secondary bus. PI7C21P100B de-asserts these pins for
at least 2 PCI clock cycles before asserting it again.
During idle and S_GNT# deasserted, PI7C21P100B will
drive S_AD, S_CBE, and S_PAR.
Secondary Grant (Active LOW):
When the internal arbiter is enabled, PI7C21P100B
asserts this pin to allow external masters to access the
secondary bus. PI7C21P100B de-asserts this pin for at
least 2 PCI clock cycles before asserting it again.
During idle and S_GNT# deasserted, PI7C21P100B will
drive S_AD, S_CBE, and S_PAR.
When the internal arbiter is disabled, this is used by
PI7C21P100B as its REQ output.
Secondary RESET (Active LOW): Asserted when any
of the following conditions are met:
1.
2.
3.
When asserted, all control signals are tri-stated and
zeroes are driven on S_AD, S_CBE, S_PAR, and
S_PAR64.
Description
Secondary Upper 32-bit Address/Data: Multiplexed
address and data bus. Address is indicated by
S_FRAME# assertion. Write data is stable and valid
when S_IRDY# is asserted and read data is stable and
valid when S_IRDY# is asserted. Data is transferred on
rising clock edges when both S_IRDY# and S_TRDY#
are asserted. During bus idle, PI7C21P100B drives
S_AD to a valid logic level when the bridge is granted
the bus.
Signal P_RESET# is asserted.
Secondary reset bit in bridge control register in
configuration space is set.
The chip reset bit in the chip control register in
configuration space is set.
2-PORT PCI-X TO PCI-X BRIDGE
November 2005 – Revision 1.02
PI7C21P100B