ADSP-TS201SABPZ060 Analog Devices Inc, ADSP-TS201SABPZ060 Datasheet - Page 15

• Manufacturer Part Number: ADSP-TS201SABPZ060
• Description: IC, FLOAT-PT DSP, 64BIT, 600MHZ, BGA-576
• Manufacturer: Analog Devices Inc
• Series: TigerSHARCr
• Type: Fixed/Floating Pointr

Specifications of ADSP-TS201SABPZ060

• Frequency: 600MHz
• Supply Voltage: 1.2V
• Embedded Interface Type: HPI
• No. Of I/o's: 4
• Supply Voltage Range: 1.14V To 1.26V, 2.38V To 2.63V
• Interface: Host Interface, Link Port, Multi-Processor
• Clock Rate: 600MHz
• Non-volatile Memory: External
• On-chip Ram: 3MB
• Voltage - I/o: 2.50V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 576-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ADZS-TS201S-EZLITE - KIT LITE EVAL FOR ADSP-TS201S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 7. Pin Definitions—External Port DMA/Flyby
Signal
DMAR3–0
IOWR
IORD
IOEN
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5 k
pull-up 500
= internal pull-up 40 k
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
imately 5 k
Ω
; pu = internal pull-up 5 k
Ω
Ω
to V
on DSP ID = 0; pd_m = internal pull-down 5 k
DD_IO
, nc = not connected; na = not applicable (always used); V
Ω
. For more pull-down and pull-up information, see
Type
I/A
O/T
(pu_0)
O/T
(pu_0)
O/T
(pu_0)
Ω
; pd_0 = internal pull-down 5 k
Term
epu
nc
nc
nc
Rev. C | Page 15 of 48 | December 2006
Description
DMA Request Pins. Enable external I/O devices to request DMA services from the DSP.
In response to DMARx, the DSP performs DMA transfers according to the DMA
channel’s initialization. The DSP ignores DMA requests from uninitialized channels.
I/O Write. When a DSP DMA channel initiates a flyby mode read transaction, the DSP
asserts the IOWR signal during the data cycles. This assertion makes the I/O device
sample the data instead of the TigerSHARC.
I/O Read. When a DSP DMA channel initiates a flyby mode write transaction, the DSP
asserts the IORD signal during the data cycle. This assertion with the IOEN makes the
I/O device drive the data instead of the TigerSHARC.
I/O Device Output Enable. Enables the output buffers of an external I/O device for fly-
by transactions between the device and external memory. Active on flyby
transactions.
Ω
Ω
on DSP bus master; pu_m = internal pull-up 5 k
on DSP ID = 0; pu_0 = internal pull-up 5 k
Electrical Characteristics on Page
DD_IO
= connect directly to V
Ω
to V
Ω
on DSP ID = 0; pu_od_0 = internal
SS
DD_IO
; epu = external pull-up approx-
22.
Ω
; V
on DSP bus master; pu_ad
SS
= connect directly to V
ADSP-TS201S
SS