DSPIC30F1010-20E/SO Microchip Technology, DSPIC30F1010-20E/SO Datasheet - Page 214

• Manufacturer Part Number: DSPIC30F1010-20E/SO
• Description: 6KB, Flash, 256bytes-RAM, 30MIPS, 21I/O, 16-bit Family,nanoWatt 28 SOIC .300in T
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F1010-20E/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 6KB (2K x 24)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC30F1010/202X
FIGURE 18-10:
18.7.1.1
The oscillator start-up circuitry is not linked to the POR
circuitry.
frequency crystals) will have a relatively long start-up
time. Therefore, one or more of the following conditions
is possible after the POR timer and the PWRT have
expired:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has NOT expired (if
• The PLL has not achieved a LOCK (if PLL is
If the FSCM is enabled and one of the above conditions
is true, then a clock failure trap will occur. The device
will automatically switch to the FRC oscillator and the
user can switch to the desired crystal oscillator in the
trap, ISR.
18.7.1.2
If the FSCM is disabled and the Power-up Timer
(PWRT) is also disabled, then the device will exit rap-
idly from Reset on power-up. If the clock source is FRC
or EC, it will be active immediately.
If the FSCM is disabled and the system clock has not
started, the device will be in a frozen state at the Reset
vector until the system clock starts. From the user’s
perspective, the device will appear to be in Reset until
a system clock is available.
DS70178C-page 212
a crystal oscillator is used).
used).
PWRT Time-out
OST Time-out
Internal Reset
Internal POR
Some
POR with Long Crystal Start-up Time
(with FSCM Enabled)
Operating without FSCM and PWRT
MCLR
V
DD
crystal
TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO V
circuits
(especially
T
OST
Preliminary
low
T
PWRT
FIGURE 18-11:
Note:
Note 1: External Power-on Reset circuit is
2: R should be suitably chosen so as to
3: R1 should be suitably chosen so as to
Dedicated supervisory devices, such as
the MCP1XX and MCP8XX, may also be
used as an external Power-on Reset
circuit.
required only if the V
is too slow. The diode D helps discharge
the capacitor quickly when V
down.
make sure that the voltage drop across
R does not violate the device’s electrical
specification.
limit any current flowing into MCLR from
external capacitor C, in the event of
MCLR/V
trostatic Discharge (ESD) or Electrical
Overstress (EOS).
D
V
DD
R
C
PP
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW V
© 2006 Microchip Technology Inc.
pin breakdown due to Elec-
R1
DD
DD
DD
dsPIC30F
MCLR
): CASE 2
POWER-UP)
power-up slope
DD
powers