ISP1105BS-T NXP Semiconductors, ISP1105BS-T Datasheet - Page 6

• Manufacturer Part Number: ISP1105BS-T
• Description: RF Transceiver USB TXRX 12/1.5MBITS
• Manufacturer: NXP Semiconductors

Specifications of ISP1105BS-T

• Number Of Receivers: 7
• Number Of Transmitters: 3
• Operating Supply Voltage: 1.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: HVQFN-16
• Maximum Data Rate: 12 Mbps
• Maximum Supply Current: 2 mA, 8 mA
• Minimum Operating Temperature: - 40 C
• Protocol Supported: USB 2.0
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISP1105BS,118

Philips Semiconductors
Table 3:
9397 750 11231
Product data
Symbol
OE
RCV
VP
VM
SUSPND
MODE
GND
V
SPEED
D
D
CC(I/O)
[1]
Pin description
pad
BS
die
ISP1105
10
1
2
3
4
5
6
7
8
9
pad
die
10
W
6.2 Pin description
1
2
3
4
5
6
7
8
9
Pin
DH
ISP1106
10
11
12
3
4
5
6
7
8
9
-
10
W
1
2
3
4
5
6
7
8
9
-
Type
I
O
O
O
I
I
-
-
I
AI/O
AI/O
Description
output enable input (CMOS level with respect to V
enables the transceiver to transmit data on the USB bus
input pad; push pull; CMOS
differential data receiver output (CMOS level with respect to V
driven LOW when input SUSPND is HIGH; the output state of RCV is
preserved and stable during an SE0 condition
output pad; push pull; 4 mA output drive; CMOS
single-ended D receiver output (CMOS level with respect to V
external detection of single-ended zero (SE0), error conditions, speed of
connected device; driven HIGH when no supply voltage is connected to
V
output pad; push pull; 4 mA output drive; CMOS
single-ended D receiver output (CMOS level with respect to V
external detection of single-ended zero (SE0), error conditions, speed of
connected device; driven HIGH when no supply voltage is connected to
V
output pad; push pull; 4 mA output drive; CMOS
suspend input (CMOS level with respect to V
low-power state while the USB bus is inactive and drives output RCV to a
LOW level
input pad; push pull; CMOS
mode input (CMOS level with respect to V
differential input mode (VPO, VMO) whereas a LOW level enables a
single-ended input mode (VO, FSE0); see
input pad; push pull; CMOS
ground supply
supply voltage for digital I/O pins (1.65 to 3.6 V). When V
connected, the (D D ) pins are in three-state; this supply pin is totally
independent of V
voltage
speed selection input (CMOS level with respect to V
slew rate of differential data outputs D and D according to the
transmission speed
LOW — low-speed (1.5 Mbit/s)
HIGH — full-speed (12 Mbit/s)
input pad; push pull; CMOS
negative USB data bus connection (analog, differential); for low-speed
mode connect to pin V
positive USB data bus connection (analog, differential); for full-speed mode
connect to pin V
Rev. 08 — 19 February 2004
CC(5.0)
CC(5.0)
and V
and V
reg(3.3)
reg(3.3)
[2]
pu(3.3)
CC(5.0)
via a 1.5 k resistor
pu(3.3)
and V
via a 1.5 k resistor
reg(3.3)
and must never exceed the V
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
CC(I/O)
Advanced USB transceivers
Table 5
ISP1105/1106
CC(I/O)
); a HIGH level enables the
CC(I/O)
and
); a HIGH level enables
CC(I/O)
Table 6
, active LOW);
CC(I/O)
); adjusts the
CC(I/O)
CC(I/O)
CC(I/O)
is not
reg(3.3)
);
); for
); for
5 of 28