SA58640DK-T NXP Semiconductors, SA58640DK-T Datasheet
SA58640DK-T
Specifications of SA58640DK-T
Related parts for SA58640DK-T
SA58640DK-T Summary of contents
Page 1
SA58640 Low-voltage mixer FM IF system Rev. 3 — 12 April 2011 1. Introduction The SA58640 was designed for cordless telephone applications in which efficient and economic integrated solutions are required and yet high performance is desirable. Although the product ...
Page 2
... NXP Semiconductors 5. Ordering information Table 1. Ordering information Type number Package Name SA58640DK SSOP20 6. Block diagram Fig 1. SA58640 Product data sheet Description plastic shrink small outline package; 20 leads; body width 4.4 mm MIXER_OUT IF_AMP_IN IF_AMP_DEC IF_AMP_DEC amp mixer RSSI OSCILLATOR RF_IN_P OSCOUT RSSI_OUT ...
Page 3
... IF amplifier decoupling 20 mixer output All information provided in this document is subject to legal disclaimers. Rev. 3 — 12 April 2011 Low-voltage mixer FM IF system 20 MIXER_OUT 19 IF_AMP_DEC 18 IF_AMP_IN 17 IF_AMP_DEC 16 IF_AMP_OUT SA58640DK 15 GND 14 LIM_IN 13 LIM_DEC 12 LIM_DEC 11 LIM_OUT 002aab134 SA58640 © NXP B.V. 2011. All rights reserved ...
Page 4
... NXP Semiconductors 8. Functional description The SA58640 signal processing system suitable for second IF systems with input frequency as high as 100 MHz. The bandwidth of the IF amplifier and limiter is at least 2 MHz with gain. The gain/bandwidth distribution is optimized for 455 kHz, 1.5 kΩ source applications. The overall system is well-suited to battery operation as well as and high quality products of all types ...
Page 5
... NXP Semiconductors 9. Limiting values Table 3. In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol stg T amb Z th 10. Static characteristics Table amb Symbol [1] RF frequency = 45 MHz; +14.5 dBV RF input step-up; IF frequency = 455 kHz; R17 = 2.4 kΩ and R18 = 3.3 kΩ; RF level = −45 dBm; FM modulation = 1 kHz with ± 5 kHz peak deviation. Audio output with de-emphasis filter and C-message weighted filter ...
Page 6
... NXP Semiconductors 11. Dynamic characteristics Table 5. Dynamic characteristics Symbol Parameter Mixer/oscillator section (external LO = 220 mV RMS value) f input frequency i f oscillator frequency osc NF noise figure IP3 input third-order intercept I point G conversion power gain p(conv input resistance i(RF input capacitance i(RF) R mixer output resistance ...
Page 7
... NXP Semiconductors 12. Performance curves (mA −55 −35 − Fig 3. Supply current versus ambient temperature 5 (1) relative level (dB) −5 −15 −25 −35 (2) −45 (3) −55 (4) −65 −125 −105 − MHz; deviation = ±5 kHz 117.6 mV. o(aud)RMS (1) Audio. (2) AM rejection. (3) THD+N. (4) Noise. Fig 5. Relative level of audio, AM rejection, THD+N ...
Page 8
... NXP Semiconductors Fig 7. 13. Application information MHz input The layout is very critical in the performance of the receiver. We highly recommend our demo board layout. All of the inductors, the quad tank, and their shield must be grounded μ μF or higher value tantalum capacitor on the supply line is essential. A low frequency ESR screening test on this capacitor will ensure consistent good sensitivity in production. A 0.1 μ ...
Page 9
... NXP Semiconductors Table 6. Component C10 C12 C14 C15 C17 C18 C19 C21 C23 C26 C27 [2] FL1 [2] FL2 IFT1 [3] R5 R10 R11 R17 R18 R19 [1] This value can be reduced when a battery is the power source. [2] This kHz bandwidth 455 kHz ceramic filter. All the characterization and testing are done with this wideband filter ...
Page 10
... MHz X1 R10 RSSI C27 C10 C9 VCC C12 GND 820 Ω 4.7 nF AUDIO_DC SA6x6DK/SA58640DK top view with components All information provided in this document is subject to legal disclaimers. Rev. 3 — 12 April 2011 SA58640 Low-voltage mixer FM IF system MHz FIL1 C1 C2 C21 C23 455 kHz ...
Page 11
... NXP Semiconductors Fig 10. SA6x6DK/SA58640DK bottom view (viewed from top) SA58640 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 12 April 2011 SA58640 Low-voltage mixer FM IF system 001aal892 © NXP B.V. 2011. All rights reserved ...
Page 12
... NXP Semiconductors 14. Test information (1) Set your RF generator at 45.000 MHz, use a 1 kHz modulation frequency and a 6 kHz deviation if (2) The measured typical sensitivity for 12 dB SINAD should be 0.45 μV or −114 dBm at the RF input. (3) The smallest RSSI voltage (i.e., when no RF input is present and the input is terminated (4) The C-message and de-emphasis filter combination has a peak gain for accurate Fig 11 ...
Page 13
... NXP Semiconductors 15. Package outline SSOP20: plastic shrink small outline package; 20 leads; body width 4 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.15 1.4 mm 1.5 0.25 0 1.2 Note 1. Plastic or metal protrusions of 0.20 mm maximum per side are not included. OUTLINE VERSION IEC SOT266-1 Fig 12 ...
Page 14
... NXP Semiconductors 16. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 16.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits ...
Page 15
... NXP Semiconductors 16.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • ...
Page 16
... NXP Semiconductors Fig 13. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 17. Abbreviations Table 9. Acronym AC AM ESD ESR NPO RF RSSI SINAD THD SA58640 Product data sheet maximum peak temperature ...
Page 17
... NXP Semiconductors 18. Revision history Table 10. Revision history Document ID Release date SA58540 v.3 20110412 • Modifications: Table 6 “Demo board application component SA58540 v.2 20110211 SA58640 v.1 20050406 SA58640 Product data sheet Data sheet status Change notice Product data sheet - list”: Product data sheet ...
Page 18
... In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or ...
Page 19
... Product data sheet NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ ...
Page 20
... NXP Semiconductors 21. Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 General description . . . . . . . . . . . . . . . . . . . . . . 1 3 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 4 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 Functional description . . . . . . . . . . . . . . . . . . . 4 9 Limiting values Static characteristics Dynamic characteristics . . . . . . . . . . . . . . . . . . 6 12 Performance curves . . . . . . . . . . . . . . . . . . . . . 7 13 Application information ...