LTC1609CSW#TRPBF Linear Technology, LTC1609CSW#TRPBF Datasheet - Page 14

• Manufacturer Part Number: LTC1609CSW#TRPBF
• Description: IC ADC SRL 16BIT 200KSPS 20-SOIC
• Manufacturer: Linear Technology

Specifications of LTC1609CSW#TRPBF

• Number Of Bits: 16
• Sampling Rate (per Second): 200k
• Data Interface: Serial
• Number Of Converters: 1
• Power Dissipation (max): 100mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIO S I FOR ATIO
LTC1609
Power Shutdown
When the PWRD pin is tied high, power consumption
drops to a typical value of 50 W from a specified maxi-
mum of 100mW. In the power shutdown mode, the result
from the previous conversion is still available in the
internal shift register, assuming the data had not been
clocked out before going into power shutdown.
The internal reference buffer and the reference are shut
down, so the power-up recovery time will be dependent
upon how fast the bypass capacitors on these pins can be
charged. If the internal reference is used, the 4k resistor in
series with the output and the external bypass capacitor,
typically 2.2 F, will be the main time constant for the
power-up recovery time. If an external reference is used,
the reference buffer output will be able to ramp from 0V to
2.5V in 1ms, while charging a typical bypass capacitor of
2.2 F. The recovery time will be less if the bypass capaci-
tor has not completely discharged.
DIGITAL INTERFACE
Internal Conversion Clock
The ADC has an internal clock that is trimmed to achieve
a typical conversion time of 2.7 s. No external adjust-
ments are required and, with the typical acquisition time of
1.5 s, throughput performance of 200ksps is assured.
Timing and Control
Conversion start and data read are controlled by two
digital inputs: CS and R/C. To start a conversion and put
14
DATACLK
DATA
BUSY
U
R/C
Figure 8. Serial Data Timing Using Internal Clock (CS, EXT/INT and TAG Tied Low)
t
1
U
t
2
W
t
8
t
10
(MSB)
B15
1
U
t
9
B14
2
t
11
B13
3
the sample-and-hold into the hold mode bring CS and
R/C low for no less than 40ns. Once initiated it cannot be
restarted until the conversion is complete. Converter
status is indicated by the BUSY output and this is low while
the conversion is in progress.
The conversion result is clocked out serially on the DATA
pin. It can be synchronized by using the internal data clock
or by using an external clock provided by the user. Tying
the EXT/INT pin high puts the LTC1609 in the external
clock mode and the DATACLK pin is a digital input. Tying
the EXT/INT pin low puts the part in the internal clock mode
and the DATACLK pin becomes a digital output.
Internal Clock Mode
With the EXT/INT pin tied low, the LTC1609 provides the
data clock on the DATACLK pin. The timing diagram is
shown in Figure 8. Typically, CS is tied low and the R/C
pin is used to start a conversion. During the conversion
a 16-bit word will be shifted out MSB-first on the DATA
pin. This word represents the result from the previous
conversion. The DATACLK pin outputs 16 clock pulses
used to synchronize the data. The output data is valid on
both the rising and falling edges of the clock. After the
LSB bit has been clocked out, the DATA pin will take on
the state of the TAG pin at the start of the conversion. The
DATACLK pin goes low until the next conversion is
requested. The data clock is derived from the internal
conversion clock. To avoid errors from occurring during
the current conversion, minimize the loading on the
DATACLK pin and the DATA pin. For the best conversion
results the external clock mode is recommended.
t
3
14
B2
15
B1
16
B0
1609 F08
1609fa