EP3C16Q240C8N Altera, EP3C16Q240C8N Datasheet - Page 28

• Manufacturer Part Number: EP3C16Q240C8N
• Description: IC CYCLONE III FPGA 16K 240PQFP
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C16Q240C8N

• Number Of Logic Elements/cells: 15408
• Number Of Labs/clbs: 963
• Total Ram Bits: 516096
• Number Of I /o: 160
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 240-MQFP, 240-PQFP
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 15408
• # I/os (max): 92
• Frequency (max): 402MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 15408
• Ram Bits: 516096
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: PQFP
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200P0037 - BOARD DEV/EDUCATION ALTERA DE0544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2458

Page 28
Design and Compilation
Design Entry
f
f
Flash Pins and other Pin Connections
For information on the flash pin connections for the AP configurations scheme, refer
to the
Handbook.
Flash for AP
In the AP configuration scheme, the commodity parallel flash is used as configuration
memory. The AP configuration controller in Cyclone III devices is designed to
interface with the Intel StrataFlash
Unlike the EPCS devices, the P30 and P33 flash families supported in the AP
configuration scheme is designed to interface with microprocessors. By configuring
from an industry standard microprocessor flash which allows access to flash after it is
in user mode, the AP configuration scheme allows you to combine configuration data
and user data (microprocessor boot code) on the same flash memory.
The Intel P30 and P33 flash families support a continuous synchronous burst read
mode at 40 MHz DCLK frequency for reading data from the flash. You must refer to
the respective flash datasheets to check for the supported speed grades and package
options. For example, the Intel P30 and P33 families have only a single speed grade at
40 MHz; however, they do not support 40 MHz on the TSOP package. Therefore, the
P30 and P33 FBGA packages are supported for the AP configuration scheme, while
the TSOP package is not supported.
For more information about the active parallel configuration scheme and its
supported parallel flash, refer to the
volume 1 of the Cyclone III Device Handbook.
This section covers topics you should look into during the design process, which
includes design entry consideration and recommendation, power consideration,
information on the Cyclone III I/O pins and PLLs, timing consideration as well as
information on performing simulation on your design.
The Quartus II software allows you to create your design through schematic/block
diagram or hardware description language (HDL) coding. The commonly used HDL
formats supported are Verilog and VHDL. For simple designs, using schematic or
block diagrams make your task of creating the design easier. However, for more
complex designs, for example designs with state machines, using HDL coding gives
you the flexibility you need, and in some cases, makes your design more efficient.
If you use HDL as the design entry for your design, pay attention to the coding style.
HDL coding has a significant effect on the quality of results in terms of logic
utilization and performance that you achieve for your designs. Effective coding helps
the synthesis tool to perform better when synthesizing your design.
Configuring Cyclone III Devices
®
Embedded Memory (P30 and P33) flash families.
chapter in volume 1 of the Cyclone III Device
Configuring Cyclone III Devices
© November 2008 Altera Corporation
chapter in
Design and Compilation