FDC37C669-MT SMSC, FDC37C669-MT Datasheet - Page 89

• Manufacturer Part Number: FDC37C669-MT
• Description: IC CTRLR SUPER I/O FLPPY 100TQFP
• Manufacturer: SMSC

Specifications of FDC37C669-MT

• Controller Type: I/O Controller
• Interface: ISA Host
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 25mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1008

IBM XT/AT COMPATIBLE, BI-DIRECTIONAL AND EPP
MODES
DATA PORT
ADDRESS OFFSET = 00H
The Data Port is located at an offset of '00H' from the
base address. The data register is cleared at initialization
by RESET.
Register latches the contents of the data bus with the
rising edge of the nIOW input. The contents of this
register are buffered (non inverting) and output onto the
PD0 - PD7 ports.
mode, PD0 - PD7 ports are buffered (not latched) and
output to the host CPU.
STATUS PORT
ADDRESS OFFSET = 01H
The Status Port is located at an offset of '01H' from the
base address. The contents of this register are latched
for the duration of an nIOR read cycle. The bits of the
Status Port are defined as follows:
BIT 0 TMOUT - TIME OUT
This bit is valid in EPP mode only and indicates that a 10
usec time out has occured on the EPP bus. A logic O
means that no time out error has occured; a logic 1
means that a time out error has been detected. This bit is
cleared by a RESET. Writing a one to this bit clears the
time out status bit. On a write, this bit is self clearing and
does not require a write of a zero. Writing a zero to this
bit has no effect.
BITS 1, 2 - are not implemented as register bits, during a
read of the Printer Status Register these bits are a low
level.
During a WRITE operation, the Data
During a READ operation in SPP
89
BIT 3 nERR - nERROR
The level on the nERROR input is read by the CPU as bit
3 of the Printer Status Register. A logic O means an
error has been detected; a logic 1 means no error has
been detected.
BIT 4 SLCT - PRINTER SELECTED STATUS
The level on the SLCT input is read by the CPU as bit 4
of the Printer Status Register. A logic 1 means the printer
is on line; a logic 0 means it is not selected.
BIT 5 PE - PAPER END
The level on the PE input is read by the CPU as bit 5 of
the Printer Status Register. A logic 1 indicates a paper
end; a logic 0 indicates the presence of paper.
BIT 6 nACK - nACKNOWLEDGE
The level on the nACK input is read by the CPU as bit
6 of the Printer Status Register. A logic 0 means that the
printer has received a character and can now accept
another. A logic 1 means that it is still processing the last
character or has not received the data.
BIT 7 nBUSY - nBUSY
The complement of the level on the nBUSY input is read
by the CPU as bit 7 of the Printer Status Register. A logic
0 in this bit means that the printer is busy and cannot
accept a new character. A logic 1 means that it is ready
to accept the next character.
CONTROL PORT
ADDRESS OFFSET = 02H
The Control Port is located at an offset of '02H' from the
base address. The Control Register is initialized by the
RESET input, bits 0 to 5 only being affected; bits 6 and 7
are hard wired low.