ICS1893BFI IDT, Integrated Device Technology Inc, ICS1893BFI Datasheet - Page 57

PHYCEIVER LOW PWR 3.3V 48-SSOP

ICS1893BFI

Manufacturer Part Number
ICS1893BFI
Description
PHYCEIVER LOW PWR 3.3V 48-SSOP
Manufacturer
IDT, Integrated Device Technology Inc
Series
PHYceiver™r
Type
PHY Transceiverr
Datasheets

Specifications of ICS1893BFI

Protocol
MII
Voltage - Supply
3.14 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
48-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Drivers/receivers
-
Lead Free Status / Rohs Status
Not Compliant
Other names
1893BFI

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICS1893BFI
Manufacturer:
OKI
Quantity:
1 934
Part Number:
ICS1893BFILF
Manufacturer:
ICS
Quantity:
20 000
7.3 Register 1: Status Register
7.3.1 100Base-T4 (bit 1.15)
ICS1893BF, Rev. F, 5/13/10
Table 7-6
and an STA. There are two types of status bits: some report the capabilities of the port, and some indicate
the state of signals used to monitor internal circuits.
The STA accesses the Status Register using the Serial Management Interface. During a reset, the
ICS1893BF initializes the Status Register bits to pre-defined, default values.
Note:
Table 7-6. Status Register (Register 1 [0x01])
† As per the IEEE Std 802.3u, during any write operation to any bit in this register, the STA must write the default value
The STA reads this bit to learn if the ICS1893BF can support 100Base-T4 operations. Bit 1.15 of the
ICS1893BF is permanently set to logic zero, which informs an STA that the ICS1893BF cannot support
100Base-T4 operations.
1.15
1.14
1.13
1.12
1.11
1.10
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
Bit
to all Reserved bits.
ICS1893BF Data Sheet Rev. F - Release
100Base-T4
100Base-TX full duplex
100Base-TX half duplex Mode not supported
10Base-T full duplex
10Base-T half duplex
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
MF Preamble
suppression
Auto-Negotiation
complete
Remote fault
Auto-Negotiation ability
Link status
Jabber detect
Extended capability
For an explanation of acronyms used in
lists the Status Register bits. These 16 bits of data provide an interface between the ICS1893BF
Definition
Always 0. (Not supported.) N/A
Mode not supported
Mode not supported
Mode not supported
Always 0
Always 0
Always 0
Always 0
PHY requires MF
Preambles
Auto-Negotiation is in
process, if enabled
No remote fault detected
N/A
Link is invalid/down
No jabber condition
N/A
When Bit = 0
Copyright © 2009, IDT, Inc.
All rights reserved.
57
Table
7-5, see
Mode supported
Mode supported
Mode supported
Mode supported
N/A
N/A
N/A
N/A
PHY does not require
MF Preambles
Auto-Negotiation is
completed
Remote fault detected
Always 1: PHY has
Auto-Negotiation ability
Link is valid/established
Jabber condition
detected
Always 1: PHY has
extended capabilities
When Bit = 1
Chapter 1, “Abbreviations and
Chapter 7 Management Register Set
cess
CW
CW
CW
CW
CW
CW
CW
CW
Ac-
RO
RO
RO
RO
RO
RO
RO
RO
SF
LH
LH
LH
LL
Acronyms”.
fault
De-
0†
0†
0†
0†
0
1
1
1
1
0
0
0
1
0
1
0
May, 2010
Hex
7
8
0
9

Related parts for ICS1893BFI