UZZ9001,118 NXP Semiconductors, UZZ9001,118 Datasheet
UZZ9001,118
Specifications of UZZ9001,118
UZZ9001 /T3
UZZ9001 /T3
Related parts for UZZ9001,118
UZZ9001,118 Summary of contents
Page 1
DISCRETE SEMICONDUCTORS DATA SHEET UZZ9001 Sensor Conditioning Electronic Product specification Supersedes data of 2000 May 19 2000 Nov 27 ...
Page 2
Philips Semiconductors Sensor Conditioning Electronic FEATURES One chip angle sensor output signal conditioning 180 angle range with KMZ41 Accuracy better than 1 together with KMZ41 Temperature range from 40 to +150 C SPI protocol SO24 package. GENERAL DESCRIPTION The UZZ9001 ...
Page 3
Philips Semiconductors Sensor Conditioning Electronic LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER V supply voltage DDA V supply voltage DD1 V supply voltage DD2 V voltage at all pins pin T storage temperature ...
Page 4
Philips Semiconductors Sensor Conditioning Electronic ELECTRICAL CHARACTERISTICS +150 4.5 to 5.5 V; typical characteristics for T amb DD specified. SYMBOL PARAMETER V supply voltage DDA V supply voltage DD1 V supply voltage DD2 ...
Page 5
Philips Semiconductors Sensor Conditioning Electronic handbook, full pagewidth The following list gives a short description of the relevant block functions: 1. The ADC block contains two Sigma Delta AD converters, sensor offset ...
Page 6
Philips Semiconductors Sensor Conditioning Electronic handbook, full pagewidth CLK 10 8 DATA note1 (1) Not defined data, normally LSB of character previously transmitted. Table 1 SPI-Timing DIAGRAM PARAMETER NUMBER 1 cycle time 2 enable lead time 3 ...
Page 7
Philips Semiconductors Sensor Conditioning Electronic handbook, full pagewidth DATA CS Sensor signal coding The sensor signal comprises 14 bits (D13 to D0) as shown in Fig.4. Bits D12 to D0 are used for the coding of the angle while D0 ...
Page 8
Philips Semiconductors Sensor Conditioning Electronic Magnet lost condition If both offset corrected input signal of sensor 1 and sensor 2 are below the lost magnet threshold then the failure ‘Magnet lost’ is assumed. Offset trimming To achieve a linear output ...
Page 9
Philips Semiconductors Sensor Conditioning Electronic Table 4 Programming of trim modes MODE enter trim mode for sensor input channel 1 enter trim mode for sensor input channel 2 leave trim mode for either input channel How to enter the trim ...
Page 10
Philips Semiconductors Sensor Conditioning Electronic Table 5 System delay and update rates of the UZZ9001 PARAMETER System delay (time elapsed until 95% of the final value is reached) max. signal frequency < 200 MHz transients (step response) Measurement update rate ...
Page 11
Philips Semiconductors Sensor Conditioning Electronic PACKAGE OUTLINE SO24: plastic small outline package; 24 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT A A ...
Page 12
Philips Semiconductors Sensor Conditioning Electronic DATA SHEET STATUS PRODUCT DATA SHEET STATUS STATUS Objective specification Development Preliminary specification Qualification Product specification Production Note 1. Please consult the most recently issued data sheet before initiating or completing a design. DEFINITIONS Short-form ...
Page 13
Philips Semiconductors Sensor Conditioning Electronic 2000 Nov 27 NOTES 13 Product specification UZZ9001 ...
Page 14
Philips Semiconductors Sensor Conditioning Electronic 2000 Nov 27 NOTES 14 Product specification UZZ9001 ...
Page 15
Philips Semiconductors Sensor Conditioning Electronic 2000 Nov 27 NOTES 15 Product specification UZZ9001 ...
Page 16
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...