STEF05PUR STMicroelectronics, STEF05PUR Datasheet

no-image

STEF05PUR

Manufacturer Part Number
STEF05PUR
Description
IC LINEAR VOLTAGE REG 10VDFPN
Manufacturer
STMicroelectronics
Datasheet

Specifications of STEF05PUR

Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-11265-2

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STEF05PUR
Manufacturer:
ST
Quantity:
6 635
Part Number:
STEF05PUR
Manufacturer:
ST
Quantity:
20 000
Features
Description
The STEF05 is an integrated electronic fuse
optimized for monitoring the output current and
the input voltage. Connected in series to the 5V
rail, it is able to protect the electronic circuitry on
its output from over current and over voltage. The
STEF05 has a controlled delay and turn-on time.
When an over load condition occurs the device
limits the output current to a predefined safe
value. If the anomalous overload condition
persists it goes to the open state, disconnecting
the load from the power supply. If a continuous
short circuit is present on the board, when the
power is re-applied, the E-fuse initially limits the
output current to a safe value and then again goes
to the open state.
The device is equipped with a thermal protection
circuit. The intervention of the thermal protection
is signalled to the board monitoring circuits
through an appropriate signal on the Fault pin.
Unlike the mechanical fuses, that must be
physically replaced after a single event, the E-fuse
does not degrade in its performances after short
May 2011
Continuous Current Typ: 3.6A
NChannel On Resistance Typ:40m
Enable/Fault Functions
Output Clamp Voltage Typ:6.65V
Under Voltage Lockout
Short Circuit Limit
Overload Current Limit
Controlled Output Voltage Ramp
Thermal Latch Typ: 165°C
Uses Tiny Capacitors
Operative Junction Temp. -40° C to 125° C
Available in DFN 3x3 10L.
Doc Number Rev 07
circuit/thermal protection interventions and it is
resetted either by re-cycling the supply voltage or
using the appropriate Enable pin.
The companion chip for the 12V power rails is also
available under the STEF12 code.
Applications
Hard disk drives
Solid State Drives (SSD)
Hard Disk and SSD arrays
Set top boxes
DVDs and Blu-Ray disc drivers
Electronic fuse for 5V line
DFN 3x3 - 10L
STEF05
www.st.com
1/17
17

Related parts for STEF05PUR

STEF05PUR Summary of contents

Page 1

Features Continuous Current Typ: 3.6A NChannel On Resistance Typ:40m Enable/Fault Functions Output Clamp Voltage Typ:6.65V Under Voltage Lockout Short Circuit Limit Overload Current Limit Controlled Output Voltage Ramp Thermal Latch Typ: 165°C Uses Tiny Capacitors Operative Junction Temp. -40° C ...

Page 2

Device block diagram 2/17 Doc Number Rev 07 STEF05 ...

Page 3

... If an additional capacitor is not required, this pin should be left open. 10 GND Ground Pin 11 Vcc Exposed pad. Positive input voltage must be connected to Vcc. Table 2. Order Codes Type STEF05 GND dv/dt Vcc En/fault I-Limit N/C NOTE Tape & Reel STEF05PUR Doc Number Rev 07 Pin Configuration Package DFN 3x3 10L. 3/17 ...

Page 4

Maximum Ratings 2 Maximum Ratings Table 3. Absolute Maximum Ratings Symbol Positive Power Supply Voltage (steady state Positive Power Supply Voltage (max 100ms) Vout/source (max 100ms) I-Limit (max 100ms) En/Fault dv/dt T Max Junction Temperature J T Storage ...

Page 5

STEF05 3 Electrical Characteristics Table 5. Electrical Characteristics for STEF05 V =5V, V =3.3V Symbol Parameter Under/Over Voltage Protection V Output Clamping Voltage Clamp V Under voltage Lockout UVLO V UVLO Hysteresis Hyst Power MOSFET Delay Time ...

Page 6

Typical Application 4 Typical Application Figure 2. Application circuit Figure 3. Typical HDD application circuit 6/17 Doc Number Rev 07 STEF05 ...

Page 7

STEF05 4.1 Operating modes 4.1.1 Turn-on. When the input voltage is applied, the Enable/Fault pin goes up to the high state, enabling the internal control circuitry. After an initial delay time of typically 500 s, the output voltage is supplied ...

Page 8

Typical Application 4.3 C calculation dv/dt Connecting a capacitor between the C output voltage ramp up time. Given the desired time interval t during which the output voltage goes from zero to his maximum value, the capacitance to be added ...

Page 9

STEF05 If this pin is left floating, since it has an internal pull-up circuitry, the output of the E-Fuse will be kept ON, in normal operating condition. In case of thermal fault the pin is pulled to an intermediate state ...

Page 10

Typical Performance Characteristics 5 Typical Performance Characteristics (The following plots are referred to the typical application circuit and, unless otherwise noted 25°C) A Figure 6. Clamping voltage vs temperature Figure 8. UVLO hysteresis vs temperature 10/17 Figure ...

Page 11

STEF05 Figure 10. Bias current (device operational) Figure 12. Current limit vs R Figure 14. V ramp-up vs Enable OUT Figure 11. ON resistance vs temperature Figure 13. Thermal latch delay vs power Limit Figure 15. V Doc Number Rev ...

Page 12

Typical Performance Characteristics Figure 16. Line transient Figure 18. Thermal latch from 2A load to short circuit 12/17 Figure 17. Startup into output short circuit Figure 19. Startup into output short circuit (fast rise) Doc Number Rev 07 STEF05 ...

Page 13

STEF05 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ...

Page 14

Package mechanical data 14/17 Doc Number Rev 07 STEF05 ...

Page 15

STEF05 7 Footprint Recommended Data Footprint Recommended Data Doc Number Rev 07 15/17 ...

Page 16

Revision History 8 Revision History Date Revision 13 May 11 07 16/17 Description of Change General review. Doc Number Rev 07 STEF05 ...

Page 17

... STEF05 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...

Related keywords