P87C52UBAA NXP Semiconductors, P87C52UBAA Datasheet - Page 18

• Manufacturer Part Number: P87C52UBAA
• Description: MCU 8-Bit 87C52 80C51 CISC 8KB EPROM 5V 44-Pin PLCC Tube
• Manufacturer: NXP Semiconductors

Specifications of P87C52UBAA

• Package: 44PLCC
• Device Core: 80C51
• Family Name: 87C52
• Maximum Speed: 33 MHz
• Ram Size: 256 Byte
• Program Memory Size: 8 KB
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Program Memory Type: EPROM
• Number Of Programmable I/os: 32
• Interface Type: UART
• Operating Temperature: 0 to 70 °C
• Number Of Timers: 3

1. L = Level activated
2. T = Transition activated
Philips Semiconductors
Interrupt Priority Structure
The 80C51/87C51 and 80C52/87C52 have a 6-source four-level
interrupt structure. They are the IE, IP and IPH. (See Figures 10, 11,
and 12.) The IPH (Interrupt Priority High) register that makes the
four-level interrupt structure possible. The IPH is located at SFR
address B7H. The structure of the IPH register and a description of
its bits is shown in Figure 12.
The function of the IPH SFR is simple and when combined with the
IP SFR determines the priority of each interrupt. The priority of each
interrupt is determined as shown in the following table:
Table 7.
NOTES:
2000 Aug 07
80C51 8-bit microcontroller family
4 K/8 K OTP/ROM low voltage (2.7 V–5.5 V),
low power, high speed (33 MHz), 128/256 B RAM
IPH.x
PRIORITY BITS
0
0
1
1
SOURCE
BIT
IE.7
IE.6
IE.5
IE.4
IE.3
IE.2
IE.1
IE.0
SP
X0
T0
X1
T1
T2
Interrupt Table
IE (0A8H)
IP.x
0
1
0
1
SYMBOL
EA
—
ET2
ES
ET1
EX1
ET0
EX0
Level 0 (lowest priority)
Level 1
Level 2
Level 3 (highest priority)
INTERRUPT PRIORITY LEVEL
INTERRUPT PRIORITY LEVEL
POLLING PRIORITY
Enable Bit = 1 enables the interrupt.
Enable Bit = 0 disables it.
FUNCTION
Global disable bit. If EA = 0, all interrupts are disabled. If EA = 1, each interrupt can be individually
enabled or disabled by setting or clearing its enable bit.
Not implemented. Reserved for future use.
Timer 2 interrupt enable bit.
Serial Port interrupt enable bit.
Timer 1 interrupt enable bit.
External interrupt 1 enable bit.
Timer 0 interrupt enable bit.
External interrupt 0 enable bit.
EA
7
1
2
3
4
5
6
—
6
ET2
5
Figure 10. IE Registers
REQUEST BITS
ES
4
TF2, EXF2
RI, TI
TP0
TF1
IE0
IE1
18
ET1
3
An interrupt will be serviced as long as an interrupt of equal or
higher priority is not already being serviced. If an interrupt of equal
or higher level priority is being serviced, the new interrupt will wait
until it is finished before being serviced. If a lower priority level
interrupt is being serviced, it will be stopped and the new interrupt
serviced. When the new interrupt is finished, the lower priority level
interrupt that was stopped will be completed.
EX1
2
HARDWARE CLEAR?
80C51/87C51/80C52/87C52
N (L)
ET0
N (L) Y (T)
1
1
Y
Y
N
N
Y (T)
EX0
0
2
VECTOR ADDRESS
Product specification
SU00571
0BH
1BH
2BH
03H
13H
23H