TEA5767HL NXP Semiconductors, TEA5767HL Datasheet
TEA5767HL
Specifications of TEA5767HL
Related parts for TEA5767HL
TEA5767HL Summary of contents
Page 1
IMPORTANT NOTICE Dear customer from August 2 2008, the wireless operations of NXP have moved to a new company, ST-NXP Wireless result, the following changes are applicable to the attached document. ● Company name - Philips ...
Page 2
... DATA SHEET TEA5767HL Low-power FM stereo radio for handheld applications Product specification Supersedes data of 2003 Nov 06 INTEGRATED CIRCUITS 2004 Sep 13 ...
Page 3
... INTERNAL PIN CONFIGURATION 14 APPLICATION INFORMATION 15 PACKAGE OUTLINE 16 SOLDERING 16.1 Introduction to soldering surface mount packages 16.2 Reflow soldering 16.3 Wave soldering 16.4 Manual soldering 16.5 Suitability of surface mount IC packages for wave and reflow soldering methods 17 DATA SHEET STATUS 18 DEFINITIONS 19 DISCLAIMERS 2 Product specification TEA5767HL ...
Page 4
... Bus enable line to switch the bus input and output lines into 3-state mode. 2 GENERAL DESCRIPTION The TEA5767HL is a single-chip electronically tuned FM stereo radio for low-voltage applications with fully integrated IF selectivity and demodulation. The radio is completely adjustment-free and only requires a minimum of small and low cost external components. The radio can be tuned to the European, US and Japanese FM bands ...
Page 5
... 22.5 kHz kHz; de-emphasis = 75 s; mod B = 300 kHz mV and including 9 % pilot kHz; f data byte 3 bit data byte 4 bit mV kHz de-emphasis = Product specification TEA5767HL MIN. TYP. MAX. UNIT 2.5 3.0 5.0 2.5 3.0 5.0 2.5 3.0 5.0 6.0 8.4 10 560 750 ...
Page 6
... V ref GAIN POWER STABILIZATION SUPPLY DEMODULATOR RESONANCE SOFT LIMITER AMPLIFIER MUTE LEVEL IF COUNTER ADC IF CENTRE FREQUENCY ADJUST I ref TEA5767HL programmable divider output SOFTWARE MUX PROGRAMMABLE PORT reference frequency divider output pilot mono 3-WIRE BUS DGND V DATA CLOCK CC(VCO) CCD 12 V CCD 22 nF Fig ...
Page 7
... FM demodulator MPX signal output reference voltage time constant for IF centre adjust decoupling IF limiter 1 decoupling IF limiter 2 gain control current for IF filter analog ground analog supply voltage RF input 1 RF ground RF input 2 time constant RF AGC switch output of synthesizer PLL loop filter 6 Product specification TEA5767HL DESCRIPTION ...
Page 8
... The synthesizer can also be clocked via pin XTAL2 at 6.5 MHz. The PLL tuning system can perform an autonomous search tuning function. 7.6 The RF AGC prevents overloading and limits the amount of intermodulation products created by strong adjacent channels. 7 Product specification TEA5767HL 24 LIMDEC2 23 LIMDEC1 22 TIFC 21 V ...
Page 9
... HIGH. When, during search, a band limit is reached, the tuning system stops at the band limit and the band limit flag bit is set to HIGH. The ready flag is also set to HIGH in this case. 8 Product specification TEA5767HL ...
Page 10
... WRITE/READ CLOCK DATA 2004 Sep 13 8.1.2 At Power-on reset the mute is set, all other bits are random. To initialize the IC all bytes have to be transferred W(write) t su(clk su(write Fig.3 3-wire bus write data. 9 Product specification TEA5767HL P - OWER ON RESET t h(write valid data mhc250 ...
Page 11
... BIT 4 BIT 3 PLL13 PLL12 PLL11 BIT 5 BIT 4 BIT 3 PLL5 PLL4 PLL3 BIT 5 BIT 4 BIT 3 SSL0 HLSI MS 10 Product specification TEA5767HL DATA BYTE 4 BIT 2 BIT 1 PLL10 PLL9 DESCRIPTION BIT 2 BIT 1 PLL2 PLL1 DESCRIPTION BIT 2 BIT DESCRIPTION DATA BYTE 5 BIT 0 (LSB) PLL8 ...
Page 12
... Sep 13 SEARCH STOP LEVEL BIT 5 BIT 4 BIT 3 BL XTAL SMUTE DESCRIPTION = 32.768 kHz; if XTAL = 0 then f xtal BIT 5 BIT 4 BIT 3 DESCRIPTION 11 Product specification TEA5767HL BIT 2 BIT 1 BIT 0 (LSB) HCC SNC MHz xtal BIT 2 BIT 1 BIT 0 (LSB) ...
Page 13
... Sep W(read) t su(clk Fig.4 3-wire bus read data. DATA BYTE 3 BIT 5 BIT 4 BIT 3 PLL13 PLL12 PLL11 12 Product specification TEA5767HL t HIGH 50 % LOW t t h(out) d(out DATA BYTE 4 BIT 2 BIT 1 PLL10 PLL9 DESCRIPTION mhc249 DATA BYTE 5 BIT 0 (LSB) PLL8 ...
Page 14
... IF5 IF4 IF3 DESCRIPTION BIT 5 BIT 4 BIT 3 LEV1 LEV0 CI3 DESCRIPTION BIT 5 BIT 4 BIT DESCRIPTION 13 Product specification TEA5767HL BIT 2 BIT 1 BIT 0 (LSB) PLL2 PLL1 PLL0 BIT 2 BIT 1 BIT 0 (LSB) IF2 IF1 IF0 BIT 2 BIT 1 BIT 0 (LSB) CI2 CI1 0 BIT 2 BIT 1 ...
Page 15
... Sep 13 CONDITIONS MIN. 0.45V 500 I = 500 300 10 100 100 14 Product specification TEA5767HL MAX. UNIT V CCD 0.2V V CCD A 450 mV 400 kHz 400 ...
Page 16
... Machine model ( 200 pF). 2. Human body model ( 100 pF). 10 THERMAL CHARACTERISTICS SYMBOL R thermal resistance from junction to ambient in free air th(j-a) 2004 Sep 13 PARAMETER note 1 note 2 note 1 note 2 PARAMETER 15 Product specification TEA5767HL CONDITIONS MIN. 0.3 +8 0.3 +8 0 +150 10 +75 200 ...
Page 17
... V CCD standby mode CCD bus enable line HIGH bus enable line LOW standby mode CCD bus enable line HIGH bus enable line LOW 16 Product specification TEA5767HL MIN. TYP. MAX. 2.5 3.0 5.0 2.5 3.0 5.0 2.5 3.0 5.0 6.0 8 ...
Page 18
... MHz MHz MHz Product specification TEA5767HL MIN. TYP. MAX. 0.1 V 0.1 V CC(VCO) 1.64 1.72 1.8 1.68 1.75 1.82 1.64 1.72 1.8 1.68 1.75 1.82 0.4 1.2 V 0.4 CCA 0.65 0.9 1 ...
Page 19
... C < T < +85 C amb data byte 1 = XX111111; data byte 2 = 11111110 data byte 1 = XX010000; data byte 2 = 00000000 data byte 4 bit data byte 5 bit data byte 4 bit data byte 4 bit Product specification TEA5767HL MIN. TYP. MAX. 150 217 140 350 230 330 430 3 ...
Page 20
... MHz xtal data byte 3 bit data byte 4 bit < 0.5 V SWPORT1 data byte 3 bit < SWPORT1 data byte 4 bit < 0.5 V SWPORT1 data byte 4 bit < SWPORT1 19 Product specification TEA5767HL MIN. TYP. MAX. 0.5 0 15.625 15.754 4.096 4.0625 500 1 +1 500 1 ...
Page 21
... MHz to 108 MHz; tune note +100 kHz MHz to 108 MHz; tune note 100 kHz MHz to 108 MHz; tune note MHz to 108 MHz; tune read mode data byte 4 bit 500 Product specification TEA5767HL MIN. TYP. MAX 215 225 235 85 94 102 ...
Page 22
... B = 300 kHz; AF data byte 4 bit mV 22.5 kHz kHz; mod de-emphasis = 75 s THD < mV kHz kHz; mod de-emphasis = mV and including 9 % pilot kHz kHz; mod data byte 3 bit data byte 4 bit Product specification TEA5767HL MIN. TYP. MAX 0.5 1.5 40 500 170 UNIT ...
Page 23
... mV and including 9 % pilot kHz kHz; mod data byte 3 bit data byte 4 bit and including 9 % pilot kHz kHz; mod data byte 3 bit data byte 4 bit Product specification TEA5767HL MIN. TYP. MAX 0 3.6 5 114 150 ...
Page 24
... AF load(L) data byte 3 bit kHz; R < load( formula for LOW side injection: = --------------------------------- - f ref + V . The radio is tuned to 98 MHz (HIGH side injection). RF1 RF2 23 Product specification TEA5767HL MIN. TYP. MAX – --------------------------------- - f ref = 50 kHz for the 13 MHz crystal or ref 100 10 225 10 ...
Page 25
... Right channel with modulation left; SNC on. (4) Noise in mono mode; soft mute on. (5) Noise in stereo mode; SNC on. (6) Total harmonic distortion kHz 2004 Sep kHz. mod Fig.5 FM characteristics 1. 24 Product specification TEA5767HL MHC247 (mV) THD (%) 4.0 3.5 3.0 2.5 2.0 1.5 1 ...
Page 26
... V AFL , V AFR (1) ( (1) Mono signal; no soft mute. (2) Noise in mono mode; no soft mute. (3) Level voltage 2.7 V. CCA 2004 Sep Fig.6 FM characteristics 2. 25 Product specification TEA5767HL MHC309 (mV) V TMUTE (V) 2.2 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1 ...
Page 27
... Philips Semiconductors Low-power FM stereo radio for handheld applications 13 INTERNAL PIN CONFIGURATION PIN SYMBOL 1 CPOUT 2 VCOTANK1 3 VCOTANK2 4 V CC(VCO) 5 DGND 6 V CCD 7 DATA 8 CLOCK 2004 Sep 13 EQUIVALENT CIRCUIT 270 1 MHC251 2 3 120 120 MHC252 7 5 MHC253 270 8 5 MHC254 26 Product specification TEA5767HL ...
Page 28
... Philips Semiconductors Low-power FM stereo radio for handheld applications PIN SYMBOL 9 WRITE/READ 10 BUSENABLE 11 SWPORT1 12 SWPORT2 13 XTAL1 14 XTAL2 15 PHASEFIL 2004 Sep 13 EQUIVALENT CIRCUIT 270 9 5 MHC255 150 10 5 MHC256 150 11 5 MHC257 150 12 5 MHC258 13 14 MHC259 15 26 MHC260 27 Product specification TEA5767HL ...
Page 29
... Philips Semiconductors Low-power FM stereo radio for handheld applications PIN SYMBOL 16 PILFIL 17 V AFL 18 V AFR 19 TMUTE 20 MPXO 2004 Sep 13 EQUIVALENT CIRCUIT 270 16 26 MHC261 MHC262 MHC263 MHC264 150 20 26 MHC265 28 Product specification TEA5767HL ...
Page 30
... Philips Semiconductors Low-power FM stereo radio for handheld applications PIN SYMBOL 21 V ref 22 TIFC 23 LIMDEC1 24 LIMDEC2 25 I gain 26 AGND 27 V CCA 2004 Sep 13 EQUIVALENT CIRCUIT 21 MHC266 MHC267 270 23 MHC268 270 24 MHC269 25 29 Product specification TEA5767HL 26 MHC270 ...
Page 31
... RF band filter coil L2 and L3 VCO coil XTAL13 13 MHz crystal C pulling capacitor for NX4025GA pull XTAL32.768 32.768 kHz crystal 2004 Sep 13 EQUIVALENT CIRCUIT 28 30 MHC271 MHC272 4 32 MHC273 VALUE TOLERANCE TYPE RC12G BB202 120 min min NX4025GA Product specification TEA5767HL MANUFACTURER Philips Philips ...
Page 32
... TIFC V ref GAIN POWER STABILIZATION SUPPLY DEMODULATOR RESONANCE SOFT LIMITER AMPLIFIER MUTE LEVEL IF ADC COUNTER IF CENTRE FREQUENCY ADJUST I ref TEA5767HL programmable divider output SOFTWARE PROGRAMMABLE MUX PORT reference frequency divider output pilot mono 3-WIRE BUS VCOTANK2 V DGND V DATA CLOCK CC(VCO) CCD 12 ...
Page 33
... Sep 2.5 scale (1) ( 0.4 0.18 7.1 7.1 9.15 0.8 0.3 0.12 6.9 6.9 8.85 REFERENCES JEDEC JEITA MS-026 detail 9.15 0.75 1 0.2 0.25 0.1 8.85 0.45 EUROPEAN PROJECTION Product specification TEA5767HL SOT358 (1) ( 0.9 0 0.5 0.5 0 ISSUE DATE 00-01-19 03-02-25 ...
Page 34
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 C and 320 C. 33 Product specification TEA5767HL ...
Page 35
... However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. 9. Hot bar soldering or manual soldering is suitable for PMFP packages. 2004 Sep 13 (1) (3) , TFBGA, (8) 34 Product specification TEA5767HL SOLDERING METHOD WAVE REFLOW not suitable suitable (4) not suitable suitable suitable ...
Page 36
... Product specification TEA5767HL DEFINITION These products are not Philips Semiconductors ...
Page 37
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited ...