SC16IS750IPW-S NXP Semiconductors, SC16IS750IPW-S Datasheet - Page 15

• Manufacturer Part Number: SC16IS750IPW-S
• Description: IC UART I2C/SPI 24-TSSOP
• Manufacturer: NXP Semiconductors

Specifications of SC16IS750IPW-S

• Features: Low Current
• Number Of Channels: 1, UART
• Fifo's: 64 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP (0.173", 4.40mm Width)
• For Use With: 568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-2235

NXP Semiconductors
SC16IS740_750_760_6
Product data sheet
7.5 Interrupts
The SC16IS740/750/760 has interrupt generation and prioritization (seven prioritized
levels of interrupts) capability. The interrupt enable registers (IER and IOIntEna) enable
each of the seven types of interrupts and the IRQ signal in response to an interrupt
generation. When an interrupt is generated, the IIR indicates that an interrupt is pending
and provides the type of interrupt through IIR[5:0].
control functions.
Table 6.
[1]
It is important to note that for the framing error, parity error, and break conditions, LSR[7]
generates the interrupt. LSR[7] is set when there is an error anywhere in the RX FIFO,
and is cleared only when there are no more errors remaining in the FIFO. LSR[4:2] always
represent the error status for the received character at the top of the RX FIFO. Reading
the RX FIFO updates LSR[4:2] to the appropriate status for the new character at the top of
the FIFO. If the RX FIFO is empty, then LSR[4:2] are all zeros.
For the Xoff interrupt, if an Xoff flow character detection caused the interrupt, the interrupt
is cleared by an Xon flow character detection. If a special character detection caused the
interrupt, the interrupt is cleared by a read of the IIR.
IIR[5:0]
00 0001
00 0110
00 1100
00 0100
00 0010
00 0000
11 0000
01 0000
10 0000
Available only on SC16IS750/SC16IS760.
Priority
level
none
1
2
2
3
4
5
6
7
Summary of interrupt control functions
Interrupt type
none
receiver line status
RX time-out
RHR interrupt
THR interrupt
modem status
I/O pins
Xoff interrupt
CTS, RTS
Single UART with I
Rev. 06 — 13 May 2008
[1]
[1]
2
Interrupt source
none
OE, FE, PE, or BI errors occur in characters in the
RX FIFO
Stale data in RX FIFO
Receive data ready (FIFO disable) or
RX FIFO above trigger level (FIFO enable)
Transmit FIFO empty (FIFO disable) or
TX FIFO passes above trigger level (FIFO enable)
Change of state of modem input pins
Input pins change of state
Receive Xoff character(s)/ special character
RTS pin or CTS pin change state from active (LOW)
to inactive (HIGH)
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
SC16IS740/750/760
Table 6
summarizes the interrupt
© NXP B.V. 2008. All rights reserved.
15 of 62