SC16C550IA44,518 NXP Semiconductors, SC16C550IA44,518 Datasheet - Page 24

• Manufacturer Part Number: SC16C550IA44,518
• Description: IC UART SOT187-2
• Manufacturer: NXP Semiconductors

Specifications of SC16C550IA44,518

• Features: Programmable
• Number Of Channels: 1, UART
• Fifo's: 16 Byte
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 44-LCC (J-Lead)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935270058518; SC16C550IA44-T; SC16C550IA44-T

Philips Semiconductors
9397 750 11619
Product data
7.4 Interrupt Status Register (ISR)
The SC16C550 provides six levels of prioritized interrupts to minimize external
software interaction. The Interrupt Status Register (ISR) provides the user with six
interrupt status bits. Performing a read cycle on the ISR will provide the user with the
highest pending interrupt level to be serviced. No other interrupts are acknowledged
until the pending interrupt is serviced. Whenever the interrupt status register is read,
the interrupt status is cleared. However, it should be noted that only the current
pending interrupt is cleared by the read. A lower level interrupt may be seen after
re-reading the interrupt status bits.
(bits 0-5) for the six prioritized interrupt levels and the interrupt sources associated
with each of these interrupt levels.
Table 12:
Table 13:
Priority
level
1
2
2
3
4
5
6
Bit
7-6
5-4
3-1
0
ISR[5]
0
0
0
0
0
0
1
Interrupt source
Interrupt Status Register bits description
Symbol
ISR[7-6]
ISR[5-4]
ISR[3-1]
ISR[0]
ISR[4]
0
0
0
0
0
1
0
Rev. 05 — 19 June 2003
Description
FIFOs enabled. These bits are set to a logic 0 when the FIFO is
not being used. They are set to a logic 1 when the FIFOs are
enabled.
INT priority bits 4-3. These bits are enabled when EFR[4] is set to
a logic 1. ISR[4] indicates that matching Xoff character(s) have
been detected. ISR[5] indicates that CTS, RTS have been
generated. Note that once set to a logic 1, the ISR[4] bit will stay a
logic 1 until Xon character(s) are received.
INT priority bits 2-0. These bits indicate the source for a pending
interrupt at interrupt priority levels 1, 2, and 3 (see
INT status.
Logic 0 or cleared = default condition.
Logic 0 or cleared = default condition.
Logic 0 or cleared = default condition.
Logic 0 = An interrupt is pending and the ISR contents may be
used as a pointer to the appropriate interrupt service routine.
Logic 1 = No interrupt pending (normal default condition).
ISR[3]
0
0
1
0
0
0
0
UART with 16-byte FIFO and IrDA encoder/decoder
Table 12 “Interrupt source”
ISR[2]
1
1
1
0
0
0
0
ISR[1]
1
0
0
1
0
0
0
ISR[0]
0
0
0
0
0
0
0
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Source of the interrupt
LSR (Receiver Line Status
Register)
RXRDY (Received Data
Ready)
RXRDY (Receive Data
time-out)
TXRDY (Transmitter
Holding Register Empty)
MSR (Modem Status
Register)
RXRDY (Received Xoff
signal) / Special character
CTS, RTS change of state
shows the data values
SC16C550
Table
12).
24 of 52