TDA1301T NXP Semiconductors, TDA1301T Datasheet
TDA1301T
Available stocks
Related parts for TDA1301T
TDA1301T Summary of contents
Page 1
... Direct communication to photodiode optics; no external preprocessing. GENERAL DESCRIPTION The TDA1301T is a fully digital servo processor which has been designed to provide all servo functions, except the spindle motor control, in two-stage three-spot compact disc systems. The device offers a high degree of integration, combined with the low additional cost of external components ...
Page 2
... Philips Semiconductors Digital servo processor (DSIC2) ORDERING INFORMATION EXTENDED TYPE NUMBER PINS TDA1301T 28 BLOCK DIAGRAM March 1994 PACKAGE PIN POSITION MATERIAL SO28L plastic Fig.1 Block diagram. 3 Product specification TDA1301T CODE SOT136A ...
Page 3
... SSD RA 22 radial actuator output FO 23 focus actuator output SL 24 sledge output SILD 25 serial interface load input SICL 26 serial interface clock input SIDA 27 serial interface data input/output V 28 digital power supply 2 DDD2 March 1994 Fig.2 Pin configuration. 4 Product specification TDA1301T ...
Page 4
... – --------------------- - – --------------------- - Where the detector set-up is assumed illustrated in Fig.3. and RL Fig.3 Diode configuration. 5 Product specification TDA1301T – 1 ( – connected to RL with an external RH – ( ...
Page 5
... TPI level generation. The initialization procedure runs in a radial open-loop situation and is 300 ms. This start-up time period may coincide with the last part of the turn table motor start-up time period. 6 Product specification TDA1301T signal is reached the n signal. ...
Page 6
... Hz. Independently, the BPF upper frequency ( 3 dB) can be fixed at 750 or 1850 Hz. Off-track counting TPI is a flag which is used to indicate whether the spot is positioned on the track (with a margin of track-pitch). 7 Product specification TDA1301T ACCESS SPEED (1) decreasing velocity minimum power to (1) sledge 1 of the ...
Page 7
... LOW). This circuit ensures proper initialization of the digital circuit and the output stages. Laser drive on The LDON pin is used to switch the laser drive OFF and ON open-drain output. When the laser is ON, the output has a high impedance. 8 Product specification TDA1301T input. ref ...
Page 8
... Pulse widths in accordance with “UZW-BO/FQ-A302 and B302” are applicable and can be found in the “Quality reference pocket-book” (ordering number 9398 510 34011). THERMAL RESISTANCE SYMBOL R from junction to ambient in free air th j-a March 1994 PARAMETER and V SSA SSD V 2000 V. 250 V. PARAMETER 9 Product specification TDA1301T MIN. MAX. UNIT 0 6 6.5 V 5.0 +5.0 mV 100 mW 65 +150 C ...
Page 9
... +85 C amb +85 C 0.75V amb DDD +85 C amb +85 C 0.8V amb DDD 10 Product specification TDA1301T TYP. MAX. UNIT 5 +85 C 15.8 A 7.9 A 1.0 1.1 V 1.5 1.65 V 2.0 2 ...
Page 10
... C amb +85 C 0.75V amb DDD = 0 0.4 V 1.8 OH DDD = 40 to +85 C; amb SSD DDD note 7 note 7 8 note 8 25 note 9 AC-coupled ext connected bias between pins 18 and 19 11 Product specification TDA1301T TYP. MAX. UNIT 1 1 0.3V V DDD 1 MHz 4 ...
Page 11
... A resistor must be connected to set the gain of the oscillator circuit. The value of the resistor depends on the crystal or resonator connected to the oscillator circuit (see also Chapter “Application information” When the TDA1301T is supplied by an external oscillator frequency, no crystal or resonator is required while the external reference resistor has different limits. ...
Page 12
... Philips Semiconductors Digital servo processor (DSIC2) APPLICATION INFORMATION March 1994 13 Product specification TDA1301T ...
Page 13
... Dimensions in mm. Fig.5 28-lead small-outline; plastic (SO28L, SOT136A). March 1994 0 2.45 0.3 2.25 0.1 14 0.49 0.25 M 0.36 1.27 (28x) 14 Product specification TDA1301T 7.6 7.4 A 10.65 10.00 1.1 1.0 2.65 0.32 2.35 0.23 1 detail A MBC236 - 1 ...
Page 14
... C. When using proper tools, all other pins can be soldered in one operation within between 270 and 320 C. (Pulse-heated soldering is not recommended for SO packages.) For pulse-heated solder tool (resistance) soldering of VSO packages, solder is applied to the substrate by dipping extra thick tin/lead plating before package placement. 15 Product specification TDA1301T - HELD SOLDERING ) ...