AT90USB647 Atmel Corporation, AT90USB647 Datasheet - Page 203

• Manufacturer Part Number: AT90USB647
• Manufacturer: Atmel Corporation

Specifications of AT90USB647

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.10 Examples of Baud Rate Setting
Table 18-9.
1.
7593K–AVR–11/09
Baud
Rate
(bps)
2400
4800
9600
14.4k
19.2k
28.8k
38.4k
57.6k
76.8k
115.2k
230.4k
250k
Max.
(1)
UBRR = 0, Error = 0.0%
UBRR
25
12
6
3
2
1
1
0
–
–
–
–
U2Xn = 0
62.5 kbps
Examples of UBRRn Settings for Commonly Used Oscillator Frequencies
f
Error
-18.6%
osc
-7.0%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
–
–
= 1.0000 MHz
These bits are reserved for future use. For compatibility with future devices, these bit must be
written to zero when UBRRH is written.
• Bit 11:0 – UBRR11:0: USART Baud Rate Register
This is a 12-bit register which contains the USART baud rate. The UBRRH contains the four
most significant bits, and the UBRRL contains the eight least significant bits of the USART baud
rate. Ongoing transmissions by the Transmitter and Receiver will be corrupted if the baud rate is
changed. Writing UBRRL will trigger an immediate update of the baud rate prescaler.
For standard crystal and resonator frequencies, the most commonly used baud rates for asyn-
chronous operation can be generated by using the UBRR settings in
UBRR values which yield an actual baud rate differing less than 0.5% from the target baud rate,
are bold in the table. Higher error ratings are acceptable, but the Receiver will have less noise
resistance when the error ratings are high, especially for large serial frames (see
Operational Range” on page
UBRR
51
25
12
8
6
3
2
1
1
0
–
–
U2Xn = 1
125 kbps
Error
-18.6%
-3.5%
-7.0%
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
UBRR
47
23
11
7
5
3
2
1
0
–
–
1
115.2 kbps
U2Xn = 0
Error[%]
196). The error values are calculated using the following equation:
f
Error
-25.0%
osc
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
= 1.8432 MHz
=
⎛
⎝
BaudRate
------------------------------------------------------- - 1
UBRR
95
47
23
15
11
BaudRate
7
5
3
2
1
0
–
230.4 kbps
U2Xn = 1
Closest Match
Error
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
UBRR
⎞
⎠
51
25
12
•
8
6
3
2
1
1
0
–
–
U2Xn = 0
125 kbps
100%
AT90USB64/128
f
Error
Table 18-9
-18.6%
osc
-3.5%
-7.0%
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
= 2.0000 MHz
UBRR
103
to
51
25
16
12
“Asynchronous
8
6
3
2
1
–
0
U2Xn = 1
250 kbps
Table
Error
-3.5%
-7.0%
0.2%
0.2%
0.2%
2.1%
0.2%
8.5%
8.5%
8.5%
0.0%
18-12.
–
203