ATxmega128A1 Atmel Corporation, ATxmega128A1 Datasheet - Page 275

• Manufacturer Part Number: ATxmega128A1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128A1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 78
• Ext Interrupts: 78
• Usb Speed: No
• Usb Interface: No
• Spi: 12
• Twi (i2c): 4
• Uart: 8
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 8
• Output Compare Channels: 24
• Input Capture Channels: 24
• Pwm Channels: 24
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

24.8.4
24.8.5
24.8.6
24.9
8077H–AVR–12/09
Combined SRAM & SDRAM Configuration
Timing
Initialization
Refresh
Figure 24-9. 4-Port SDRAM configuration
The Clock Enable (CKE) signal is required for SDRAM when the EBI is clocked at 2x the CPU
clock speed.
Configuring Chip Select 3 to SDRAM will enable the initialization of the SDRAM. The “Load
Mode Register” command is automatically issued at the end of the initialization. For the correct
information to be loaded to the SDRAM, one must do one of the following:
1.
2.
initialized.
The SDRAM initialization is non-interruptible by other EBI accesses.
The EBI will automatically handle the refresh of the SDRAM as long as the refresh period is con-
figured. Refresh will be done as soon as available after the refresh counter reaches the period.
The EBI can collect up to 4 refresh commands in case the interface is busy on another chip
select or in the middle of a read/write at a time a refresh should have been performed.
Combined SRAM and SDRAM configuration enables the EBI to have both SDRAM and SRAM
connected at the same time. This only available for devices with 4 port EBI interface.
10 on page 276
Configure SDRAM control registers before enabling Chip Select 3 to SDRAM.
Issue a “Load Mode Register” command and perform a dummy-access after SDRAM is
EBI
shows the configuration with all interface signals.
CAS/RE
BA[1:0]
CS[3:0]
A[11:8]
A[7:0]]
D[7:0]
DQM
CKE
RAS
CLK
WE
CLK
CKE
BA[1:0]
DQM
WE
RAS
CAS
D[7:0]
A[7:0]
A[11:8]
CS
SDRAM
XMEGA A
Figure 24-
275