AD9212 Analog Devices, AD9212 Datasheet - Page 39

• Manufacturer Part Number: AD9212
• Description: Octal, 10-Bit, 40 MSPS/65 MSPS, Serial LVDS, 1.8 V ADC
• Manufacturer: Analog Devices

Specifications of AD9212

• Resolution (bits): 10bit
• # Chan: 8
• Sample Rate: 65MSPS
• Interface: LVDS,Ser
• Analog Input Type: Diff-Uni
• Ain Range: (2Vref) p-p,2 V p-p
• Adc Architecture: Pipelined
• Pkg Type: CSP

Data Sheet
ALTERNATIVE ANALOG INPUT DRIVE
CONFIGURATION
The following is a brief description of the alternative analog
input drive configuration using the AD8334 dual VGA. If this
drive option is in use, some components may need to be populated,
in which case all the necessary components are listed in Table 17.
For more details on the AD8334 dual VGA, including how it works
and its optional pin settings, consult the
To configure the analog input to drive the VGA instead of the
default transformer option, the following components need to
be removed and/or changed.






In this configuration, L505 to L520 and L605 to L620 are populated
with 0 Ω resistors to allow signal connection and use of a filter if
additional requirements are necessary.
Remove R102, R115, R128, R141, R161, R162, R163, R164,
R202, R208, R218, R225, R234, R241, R252, R259, T101,
T102, T103, T104, T201, T202, T203, and T204 in the
default analog input path.
Populate R101, R114, R127, R140, R201, R217, R233, and
R251 with 0 Ω resistors in the analog input path.
Populate R152, R153, R154, R155, R156, R157, R158, R159,
R215, R216, R229, R230, R247, R248, R263, R264, C103,
C105, C110, C112, C117, C119, C124, C126, C203, C205,
C210, C212, C217, C219, C224, and C226 with 10 kΩ
resistors to provide an input common-mode level to the
ADC analog inputs.
Populate R105, R113, R118, R124, R131, R137, R151, R160,
R205, R213, R221, R222, R237, R238, R255, and R256 with
0 Ω resistors in the ADC analog input path to connect the
VGA outputs.
Remove R515, R520, R527, R532, R615, R620, R627, and
R632 on the AD8334 analog outputs.
Remove R512, R524, R612, and R624 to set the AD8334
mode and AD8334 HILO pin low. Some applications may
require this to be different. Consult the AD8334 data sheet
for more information on these functions.
AD8334
data sheet.
Rev. E | Page 39 of 56
In this example, a 16 MHz, two-pole low-pass filter was applied
to the AD8334 outputs. The following components need to be
removed and/or changed:



Figure 72. Example Filter Configured for 16 MHz, Two-Pole Low-Pass Filter
(Analog Input Signal = −1.03 dBFS, SNR = 56.75 dBc, SFDR = 64.4 dBc)
Remove L507, L508, L511, L512, L515, L516, L519, L520,
L607, L608, L611, L612, L615, L616, L619, and L620 on the
AD8334 analog outputs.
Populate L507, L508, L511, L512, L515, L516, L519, L520,
L607, L608, L611, L612, L615, L616, L619, and L620 with
680 nH inductors.
Populate C543, C547, C551, C555, C643, C647, C651, and
C655 with a 68 pF capacitor.
16 MHz, Two-Pole Low-Pass Filter Applied to the AD8334 Outputs
–100
–120
–20
–40
–60
–80
0
0
2.5
Figure 73. AD9212 FFT Example Results Using
5.0 7.5
680nH
680nH
10.0
FREQUENCY (MHz)
12.5
15.0 17.5
f
AIN = 3.5MHz
AD8334 = MAX GAIN SETTING
SAMPLE
20.0 22.5 25.0 27.5 30.0 32.5
68pF
= 65MSPS
AD9212