LM239PT STMicroelectronics, LM239PT Datasheet - Page 5

• Manufacturer Part Number: LM239PT
• Description: IC COMPARTR QUAD BIPOLAR 14TSSOP
• Manufacturer: STMicroelectronics
• Type: General Purposer

Specifications of LM239PT

• Number Of Elements: 4
• Output Type: CMOS, DTL, ECL, MOS, Open-Collector, TTL
• Voltage - Supply: 2 V ~ 36 V, ±1 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Number Of Channels: 4 Channels
• Response Time: 1.3 us
• Offset Voltage (max): 5 mV
• Input Bias Current (max): 250 nA
• Supply Voltage (max): 36 V
• Supply Voltage (min): 2 V
• Supply Current (max): 2 mA
• Maximum Power Dissipation: 710 mW
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Comparator Type: Low Power
• No. Of Comparators: 4
• Ic Output Type: CMOS, MOS, TTL, DTL, ECL
• Output Compatibility: CMOS, DTL, ECL, MOS, TTL
• Supply Current: 1.3mA
• Rohs Compliant: Yes
• Number Of Elements: 4
• Technology: Bipolar
• Input Offset Voltage: 5mV
• Input Bias Current (typ): 250nA
• Single Supply Voltage (typ): 3/5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12/±15V
• Power Supply Requirement: Single/Dual
• Voltage Gain In Db: 106.02dB
• Single Supply Voltage (min): 2V
• Single Supply Voltage (max): 32V
• Dual Supply Voltage (min): ±1V
• Dual Supply Voltage (max): ±16V
• Power Dissipation: 710mW
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4044-2

LM139, LM239, LM339
Table 3.
1. At output switch point, V
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant,
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
4. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the
5. The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals, 300 ns can be
Symbol
trel
independent of the state of the output, so no loading charge exists on the reference of input lines.
The upper end of the common-mode voltage range is V
damage.
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than
-0.3 V (or 0.3 V below the negative power supply, if used).
obtained.
Large signal response time
R
V
(ref)
Electrical characteristics at V
(unless otherwise specified) (continued)
L
= 5.1 kΩ connected to V
= +1.4 V
o
Parameter
≈ 1.4 V, V
CC
+
CC
from 5 V to 30 V, and over the full common-mode range (0 V to V
+
, e
l
= TTL,
Doc ID 2159 Rev 2
CC
+
CC
= +5 V, V
+
Min.
-1.5 V, but either or both inputs can go to +30 V without
LM139A - LM239A
LM339A
Typ.
300
CC
-
= GND, T
Max.
amb
= +25° C
Min
Electrical characteristics
LM139 - LM239
Typ.
300
LM339
CC
Max.
+
-1.5 V).
Unit
ns
5/16