1410210-1 TE Connectivity, 1410210-1 Datasheet - Page 3

• Manufacturer Part Number: 1410210-1
• Manufacturer: TE Connectivity
• Series: Noner

Specifications of 1410210-1

• Product Type: Connector
• Type Of Connector: Backplane
• Mount Angle: Vertical
• Module Type: Center
• Data Rate (gb/s): 3.125
• Solder Tail Contact Plating: Tin-Lead over Nickel
• Card Slot Pitch (mm [in]): 25.4 [1]
• Number Of Columns: 16
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold
• Housing Material: Liquid Crystal Polymer (LCP)
• Housing Color: Black
• Ul Flammability Rating: UL 94V-0
• Density: 141 lines/inch
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant

W ithstanding voltage.
Tem perature rise vs current.
Vibration, sinusoidal.
Mechanical shock.
Durability.
Mating force.
Unm ating force.
Com pliant pin insertion.
Com pliant pin retention.
Rev D
Test Description
1 m inute hold with no breakdown or
flashover.
30 C m axim um tem perature rise at
1 am pere load, single circuit in free
air using therm ography.
No discontinuities of 1 m icrosecond
or longer duration.
See Note.
No discontinuities of 1 m icrosecond
or longer duration.
See Note.
See Note.
0.75 N [2.7 ozf] m axim um per
contact. Average for entire
connector.
0.15 N [.54 ozf] m inim um per
contact. Average for entire
connector.
31 N [7 lbf] m axim um per pin
average.
13.35 N [3 lbf] m inim um .
Figure 1 (continued)
MECHANICAL
Requirem ent
EIA-364-20, Condition I.
500 volts AC peak or DC at sea
level.
Test between any adjacent pair of
signal contacts, or from any signal
contact to an adjacent ground pin of
m ated specim ens.
EIA-364-70, Method 1.
Stabilize at a single current level
until 3 readings at 5 m inute intervals
are within 1 C.
EIA-364-28, Test Condition II.
Subject m ated specim ens to 10-
500-10 Hz traversed in 15 m inutes
with 1.5 m m [.06 in] m axim um total
excursion. Two hours in each of 3
m utually perpendicular planes.
EIA-364-27, Method H.
Subject m ated specim ens to 30 G's
half-sine shock pulses of 11
m illiseconds duration. Three shocks
in each direction applied along 3
m utually perpendicular planes, 18
total shocks.
EIA-364-9.
Mate and unm ate specim ens for
200 cycles at a m axim um rate of
500 cycles per hour.
EIA-364-13.
Measure force necessary to m ate
specim ens at a m axim um rate of
12.7 m m [.5 in] per m inute.
EIA-364-13.
Measure force necessary to unm ate
specim ens at a m axim um rate of
12.7 m m [.5 in] per m inute.
AMP Spec 109-41.
Measure force necessary to
correctly apply a connector
assem bly to a printed circuit board
at a m axim um rate of 12.7 m m [.5
in] per m inute.
AMP Spec 109-30.
Measure force necessary to unseat
a single pin in a correctly applied
connector assem bly from its printed
circuit board hole at a m axim um
rate of 12.7 m m [.5 in] per m inute.
Procedure
108-2072
3 of 10