EP4CE15F17C9LN Altera Corporation, EP4CE15F17C9LN Datasheet - Page 7

• Manufacturer Part Number: EP4CE15F17C9LN
• Description: IC CYCLONE IV FPGA 15K 256FBGA
• Manufacturer: Altera Corporation
• Series: CYCLONE® IV Er

Specifications of EP4CE15F17C9LN

• Number Of Logic Elements/cells: 15408
• Number Of Labs/clbs: 963
• Total Ram Bits: 516096
• Number Of I /o: 165
• Number Of Gates: -
• Voltage - Supply: 0.97 V ~ 1.03 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 256-BGA
• Lead Free Status: Lead free
• Rohs Status: RoHS Compliant

Chapter 1: Cyclone IV Device Datasheet
Operating Conditions
Table 1–6. I/O Pin Leakage Current for Cyclone IV Devices
Table 1–7. Bus Hold Parameter for Cyclone IV Devices (Part 1 of 2)
November 2011 Altera Corporation
I
I
Notes to
(1) This value is specified for normal device operation. The value varies during device power
(2) The 10 A I/O leakage current limit is applicable when the internal clamping diode is off. A higher current can be observed when the diode is on.
Bus hold
low,
sustaining
current
Bus hold
high,
sustaining
current
Bus hold
low,
overdrive
current
Bus hold
high,
overdrive
current
Symbol
I
OZ
Parameter
1.8, 1.5, and 1.2 V).
Table
DC Characteristics
Input pin leakage current
Tristated I/O pin leakage
current
1–6:
V
(maximum)
V
(minimum)
0 V < V
0 V < V
IN
IN
Parameter
Condition
> V
< V
IL
IL
IN
IN
This section lists the I/O leakage current, pin capacitance, on-chip termination (OCT)
tolerance, and bus hold specifications for Cyclone IV devices.
Supply Current
The device supply current requirement is the minimum current drawn from the
power supply pins that can be used as a reference for power size planning. Use the
Excel-based early power estimator (EPE) to get the supply current estimates for your
design because these currents vary greatly with the resources used.
I/O pin leakage current for Cyclone IV devices.
Bus Hold
The bus hold retains the last valid logic state after the source driving it either enters
the high impedance state or is removed. Each I/O pin has an option to enable bus
hold in user mode. Bus hold is always disabled in configuration mode.
Table 1–7
< V
< V
CCIO
CCIO
Min
lists bus hold specifications for Cyclone IV devices.
–8
—
—
8
1.2
V
V
I
O
–125
Max
= 0 V to V
125
= 0 V to V
—
—
Conditions
Min
–12
12
—
—
CCIOMAX
CCIOMAX
1.5
–175
Max
175
—
—
(1),
(2)
Min
–30
30
—
—
Device
1.8
—
—
(1)
–200
Max
—Preliminary
200
V
—
—
CCIO
(V)
-
up. This applies for all V
Min
–50
50
—
—
2.5
–300
Max
Min
300
–10
–10
—
—
Min
–70
70
—
—
3.0
Typ
—
—
Cyclone IV Device Handbook,
CCIO
–500
Max
500
—
—
Table 1–6
settings (3.3, 3.0, 2.5,
Min
–70
Max
70
—
—
10
10
3.3
lists the
–500
Max
500
—
—
Volume 3
Unit
A
A
1–7
Unit
A
A
A
A