BGB110 NXP Semiconductors, BGB110 Datasheet
BGB110
Related parts for BGB110
BGB110 Summary of contents
Page 1
... DISCRETE SEMICONDUCTORS DATA SHEET BGB110 Bluetooth radio module Objective specification 2000 Oct 03 ...
Page 2
... MHz system clock output for baseband processor • 2.048 MHz clock output for PCM voice codecs. DESCRIPTION The BGB110 TrueBlue Bluetooth radio module is a short-range radio transceiver for wireless links operating in the globally available ISM band, between 2402 and 2480 MHz composed of a fully integrated, ...
Page 3
... Oct 03 bottom view Fig.1 Simplified outline 3 Objective specification BGB110 ...
Page 4
... BER = 0.1 % under standard conditions VS_VCO Supply VCO tank decoupling Interface RF IC adapter IC Supply RX balun + decoupling filter VS_DIG VS_ANA2 GND Fig.2 Block diagram. 4 Objective specification BGB110 MIN. TYP. MAX. 2.8 3 3.6 30 − − 65 − − 43 − − − 37 − 1 − ...
Page 5
... A 2.048 MHz clock for PCM voice codecs. JTAG interface The JTAG serial interface is used to control the BGB110. The BGB110 has to be the only slave on the JTAG bus, it does not allow for multi-slave operation. The JTAG interface protocol used is fully compliant with the standard set out in IEEE Std 1149.1-1990. The following features are supported: • ...
Page 6
... Capture-DR 0 Shift- Exit1-DR 0 Pause- Exit2- Update- SI_CLK t SI_CLK2 SI_CLK2 t SI_CLK 6 Objective specification BGB110 Select-IR-Scan Capture-IR 0 Shift- Exit1-IR 0 Pause- Exit2-IR 1 Update- MIN. TYP. MAX. 200 250 − − 20 − ...
Page 7
... Philips Semiconductors Bluetooth radio module Registers The following registers are important for setting up a Bluetooth link with the BGB110. They are controlled over the serial interface. REGISTER S_EN_WIDTH R/W CHANNEL W RSSI R XO_Trim CONTROL R/W ENABLE R/W GFSK_TABLE R/W S_EN_WIDTH The S_EN_WIDTH register is used to control the amount of time that the RF frequency synthesizer has to switch from one frequency to the next, and to settle down. It defaults to 200 µ ...
Page 8
... XIN and XOUT Bit b1 add 0.1875 pF to XIN and XOUT Bit b0 add 0.09375 pF to XIN and XOUT ID The ID register is used to identify the BGB110 set from the baseband. This is read only Bits b7 -b0 ID radio chip set identification (value = 0xA1) ...
Page 9
... Reset The BGB110 has an internal power-on reset function, which is operational every time the supply voltage is switched on. This will reset all internal registers and will bring the device into a known state. Next to the built-in power-on reset, there is the POR_EXT reset signal. This will also reset the device and put it into the same state as the power-on reset. The POR_EXT signal is intended to be used as a reset from a host processor ...
Page 10
... LPO_CLK Transmit mode The BGB110 TrueBlue Bluetooth radio module contains a fully integrated transmitter function. The RF channel frequency is selected in a conventional synthesizer, which is controlled via the serial JTAG interface. After the RF frequency has settled, the power amplifier is switched on and the modulation input is preset to its mean value. The RF frequency is allowed to resettle, to overcome possible frequency pulling effects, and the synthesizer loop is opened ...
Page 11
... T ambient temperature amb T junction temperature j Notes 1. Pins short-circuited internally must be short-circuited externally. THERMAL CHARACTERISTICS SYMBOL R thermal resistance from junction to ambient th j-a 2000 Oct 03 CONDITIONS note 1 PARAMETER 11 Objective specification BGB110 MIN. MAX. UNIT 3.6 V −0 −0.3 S − 0.01 V tbd W − 0 dBm − +125 − ...
Page 12
... MHz offset; measured in − 100 kHz bandwidth; referred to wanted channel normalized Ω − o referred to wanted output level; − 2450 MHz; RF − 1225 MHz VCO − − 12 Objective specification BGB110 MIN. TYP. MAX. UNIT 3.0 3 tbd mA 65 tbd mA 43 tbd mA 37 tbd mA 1 ...
Page 13
... GSM tbd modulated signal between 880 and 915 MHz (GSM−900 uplink) wanted signal −67dBm; GSM tbd modulated signal between 1800 and 1785 MHz (GSM−1800 uplink) 13 Objective specification BGB110 MIN. TYP. MAX. UNIT tbd −36 dBm tbd dBm −30 ...
Page 14
... The VCO frequency is one-half the RF frequency. 2000 Oct 03 CONDITIONS 30 MHz to 1 GHz − 1 GHz to 12.75 GHz − measured at 2450MHz − −0.5 2.4 − HIGH or LOW level −10 1 − − 14 Objective specification BGB110 MIN. TYP. MAX. UNIT tbd tbd dBc tbd tbd dBc tbd -47 dBc 2.1 − ...
Page 15
... Ultrasonic cleaning should not be used since this can cause serious damage to the product. 2000 Oct 03 300 handbook, halfpage T (°C) 200 100 Fig.7 Recommended reflow temperature profile. Packing An extended packing / SMD specification can be found in document RNR-T49D-2183. 15 Objective specification BGB110 MGM159 (min) ...
Page 16
... Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 16 Objective specification BGB110 (1) ...
Page 17
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...