S1M1V085 Epson Electronics America, Inc., S1M1V085 Datasheet
S1M1V085
Related parts for S1M1V085
S1M1V085 Summary of contents
Page 1
... It is possible to control the data width by the data byte control for Word-mode. 3-state output allows easy expansion of memory capacity. The temperature range of the S1M1V085B0J7 is from – and it is suitable for the industrial products. FEATURES Fast Access time ...
Page 2
... Chip Select1 CS2 Chip Select2 LB LOWER Byte Enable (Word-mode use) UB UPPER Byte Enable (Word-mode use) I/ Data I/O CIO Word-mode/Byte-mode Selection V Power Supply (2.4V to 3.0V Power Supply (0V connection 2 S1M1V085B0J CIO A16 A15 A14 A13 I/O16 I/O15 A12 A10 A11 I/O7 I/ ...
Page 3
... I DDO I = 0mA I/O = 2.85V DD Conditions ADD ADD I/O I/O S1M1V085B0J7 + 0 0.3 DD (Ta = – 2.4 to 3.0V Typ. Max. 2.7 3.0 0.0 0.0 – V +0.3 DD – 0.3 (V =0V – 2 Min. Typ. Max. –1.0 – 1.0 –1.0 – ...
Page 4
... Ta = – S1M1V085B0J7 Unit 2.4 to 3.0V Max. – ns – ns – ns – ns – ns – ns – ns – ns – ns – – ns (2.4V to 3.0V) DD (2.4V to 3.0V 5pF (Includes Jig Capacitance) ...
Page 5
... CS1 CS2 LB I/ (Dout (Din – – – CS2, output buffer "Hi-Z" state even if O S1M1V085B0J7 * CW1 t CW2 High CW1 ...
Page 6
... S1M1V085B0J7 Timing Chart (Byte-mode) *1 Read Cycle 18,SA t ACC t ACS1 CS1 t CLZ1 CS2 t ACS2 t CLZ2 OLZ I/ (Dout) *2, *3 Write Cycle 2 (CS2 Control 18, CW1 CS1 CW2 CS2 High-Z I/ (Dout) (Din) – – Note : ...
Page 7
... High-Z High Data Out Data High-Z for Byte-mode. SS – – – – – "High". S1M1V085B0J7 MODE Not Selected DDS , DDS1 Not Selected I I DDS , DDS1 Output disable I I DDA , DDA1 Output disable I I DDA , DDA1 ...
Page 8
... S1M1V085B0J7 Byte-mode (1) Reading data from byte Data is able to read when address and SA are set while holding C – – and "High". Since I/O pins are in "Hi-Z" state when O access time is apparently able to be cut down. Writing data Word-mode (1)Writing data into lower byte There are the following four ways of writing data into the memory. i) Hold CS2 = " ...
Page 9
... In case of the data retention in the standby mode, the power supply can be gone down till the specified voltage. But it is impossible to write or read in this mode. Rev.1.0 – – – – UB, LB, and data are inhibited. 0.2V, there is almost no current flow except through the high resistance S1M1V085B0J7 9 ...
Page 10
... S1M1V085B0J7 PACKAGE DIMENSIONS TFBGA-48 pin BOTTOM VIEW 0.35 0.05 SIDE VIEW TOP VIEW INDEX 0.75 Typ. 10.0 0 SRAM Die Base Tape Unit : mm Rev.1.0 ...
Page 11
... Rev.1.0 THIS PAGE IS BLANK. S1M1V085B0J7 11 ...
Page 12
... S1M1V085B0J7 NOTICE: No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products ...