ADC601JG Burr-Brown Corporation, ADC601JG Datasheet - Page 3

• Manufacturer Part Number: ADC601JG
• Description: 12-bit 900ns Analog-to-digital Converter
• Manufacturer: Burr-Brown Corporation

PACKAGE INFORMATION
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix D of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
* Same specifications as for ADC601JG.
NOTES: (1) Over or under range on the analog input results in constant maximum or minimum digital output. (2) FSR = Full Scale Range. (3) Adjustable to zero.
(4) Dynamic tests are performed using SHC804 with ADC601 unless otherwise specified. Performance may vary depending upon choice of sample/hold. (5) See Typical
Performance Curves. (6) dBc = level referred to carrier input signal = 0dB; f
input test signals. If referred to the peak envelope signal ( 0dB), the intermodulation products will be 6dB lower. For example, unit connected for 10V has 20V FSR.
(8) Temperature ranges refer to case temperature. Thermal resistance was measured on a small (5" diameter) handwired circuit board; with the test device in a (zero
insertion force) socket. Thermal resistance will be lower if the ADC601 is soldered into the PC board, a ground plane is used directly underneath the package, multiple
PC board layers are used, or forced air cooling is employed. Use heat sinking if necessary to keep the case at specified and operating temperatures.
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
ELECTRICAL
T
+V
Digital Inputs ..................................................................................... +5.5V
Analog Inputs ...................................................................................... V
Comparator Input ............................................................... –3.7V to +0.7V
Case Temperature ......................................................................... +125 C
Junction Temperature .................................................................... +165 C
Storage Temperature ...................................................... –65 C to +150 C
Stresses above these ratings may permanently damage the device.
CASE
PARAMETER
MODEL
ADC601JG
ADC601KG
POWER SUPPLY REQUIREMENTS
Supply Voltages: +V
Supply Currents: +I
Power Consumption
Thermal Resistance,
TEMPERATURE RANGE
Specification
Operating
V
CC
DD
= +25 C, 900ns conversion time, V
................................................................................................... 18V
.................................................................................................... +7V
–V
+V
–I
+I
CC
CC
DD
CC
CC
DD
JC
32-Pin Hermetic DIP
32-Pin Hermetic DIP
(8)
PACKAGE
(1)
CC
(CONT)
= 15V, +V
PACKAGE DRAWING
Nominal V
DD
= +5V, and 6-minute warm-up in a normal convection environment unless otherwise noted.
NUMBER
CONDITIONS
172–2
172–2
CC
and +V
CC
C
DD
= input frequency; f
3
ORDERING INFORMATION
Basic Model Number
Performance Grade Code
Package Code
+14.25
–14.25
+4.75
MIN
–25
J, K: 0 C to +70 C Case Temperature
G: Ceramic DIP
0
ADC601JG
S
= sampling frequency. (7) IMD is referred to the larger of the two
TYP
+15
–15
–65
5.4
1.3
+5
53
25
+15.75
–15.75
MAX
+5.25
–84.5
68.9
+70
+85
7.0
1.7
MIN
*
*
*
*
*
ADC601KG
ADC601
TYP
*
*
*
*
*
*
*
*
ADC601
MAX
*
*
*
*
*
*
*
*
*
*
( )
UNITS
mA
mA
mA
C/W
W
V
V
V
C
C
G
®