ACS-1024-LG Photon Vision Systems, Inc., ACS-1024-LG Datasheet - Page 11

• Manufacturer Part Number: ACS-1024-LG
• Description: Image Sensor, CMOS|CCD, 1026x1026 Pixels, 132pin LCC
• Manufacturer: Photon Vision Systems, Inc.

48
49
50
51
52
53
54
55
56
57
58
59
59
60
61
62
63
64
65
66
67
68
69
70
K13
K14
K15
H14
H15
H13
G13
G15
L15
Product DATASHEET ACS PDS0003 Subject to change without notice. Page 11 of 26
J14
J13
J15
PAUSE
MASTER
GAIN1
GAIN0
OFFSET1
OFFSET0
DIG_PAD_GND
DIG_PAD_PWR
_____
N_CS
______
N_WR
SYNC
TX
Photon Vision Systems, Inc.
Digital Input
0 - Transfer and read
1 - Transfer and pause
Digital Input
1 - SLAVE Mode
0 - MASTER Mode
Digital Input
Value (Hex) of G0, G1,
F0, F1. See Control
Register 0.
Digital Input
See table, pin 50.
Digital Input
See table, pin 50.
Digital Input
See table, pin 50.
Digital Pad Power
Ground
Digital Pad Power
5.0 VDC
Digital Input
Digital Input
Digital Input
Digital Input
Copyright© 2002 Rev A
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
Pin must be connected whenever in SLAVE mode, do not float.
In master mode if PAUSE Control bit Control Register 1 bit 7 is
set TRUE the controller will wait for Pin 48 to go TRUE LOW
before readout will begin.
Pin must be connected whenever in SLAVE mode, do not float.
MASTER/SLAVE Mode select. When OFF, device is in
MASTER mode. When ON, device is in SLAVE Mode. When in
MASTER mode, those signals indicated with the 'M/S' symbol
indicate that the function of these signals is depends on the
selected Mode. Typically when the device is in MASTER mode,
the 'M/S' signals like the row and column address buses output the
currently accessed pixel. When in SLAVE mode, the 'M/S' signals
are used to externally access these buses for random access.
GAIN and OFFSET control. Works in conjunction with pins 51 -
53. Default is 1X gain and no offset.
Pin must be connected whenever in SLAVE mode, do not float.
(Volts)
S1 -
S2 -
S3 -
S4 -
S5 -
S6 -
S7 -
S8 -
S9 -
S10 -
S11 -
S12 -
S13 –
S14 -
S15 -
S16 -
GAIN and OFFSET control. Works in conjunction with pins 50,
51, and 52
Pin must be connected whenever in SLAVE mode, do not float.
GAIN and OFFSET control. Works in conjunction with pins 50,
51, and 52
Pin must be connected whenever in SLAVE mode, do not float.
GAIN and OFFSET control. Works in conjunction with pins
50,51 and 52
Pin must be connected whenever in SLAVE mode, do not float.
Ground for Digital Pads
Power for Digital Pads
Controls direction of REG_DATA lines, pins 112 - 116 and pins
1-7, by reading or writing to setup registers. Works in conjunction
with pin 57. See SETUP REGISTER TIMING diagrams for
details.
Pin must be connected whenever in SLAVE mode, do not float.
Controls direction of REG_DATA lines, pins 112 - 116 and pins
1-7, by reading or writing to setup registers. Works in conjunction
with pin 54. See
SETUP REGISTER TIMING diagrams for details.
Pin must be connected whenever in SLAVE mode, do not float.
In master mode if Register 0 bit 4 is set controller will wait for pin
58 to go TRUE LOW before leaving state 0 and beginning a new
cycle.
Pin must be connected whenever in SLAVE mode, do not float.
In slave mode, when TRUE LOW TX performs a global transfer
of the charge from the collection site to the storage site
Pin must be connected whenever in SLAVE mode, do not float.
GAIN SETTING
1.00
1.33
2.00
4.00
1.00
1.33
1.33
1.00
2.00
1.33
2.00
4.00
1.00
1.00
2.00
4.00
OFFSET SETTING
-0.60
-0.90
-0.60
-0.30
-0.90
-0.90
-0.60
-0.90
-0.90
0.00
0.00
0.30
0.60
0.90
0.00
0.00