IDT7028 Integrated Device Technology, IDT7028 Datasheet - Page 16

• Manufacturer Part Number: IDT7028
• Description: 64k X16 Dual-port Ram
• Manufacturer: Integrated Device Technology

another task and occasionally attempt again to gain control of the token via
the set and test sequence. Once the right side has relinquished the token,
the left side should succeed in gaining control.
a zero into a semaphore latch and is released when the same side writes
a one to that latch.
memory space from the Dual-Port RAM. This address space is accessed
by placing a LOW input on the SEM pin (which acts as a chip select for the
semaphore flags) and using the other control pins (Address, CE, and
R/W) as they would be used in accessing a standard Static RAM. Each
of the flags has a unique address which can be accessed by either side
through address pins A
the other address pins has any effect.
is written into an unused semaphore location, that flag will be set to a zero
on that side and a one on the other side (see Table VI). That semaphore
can now only be modified by the side showing the zero. When a one is
written into the same location from the same side, the flag will be set to a
one for both sides (unless a semaphore request from the other side is
pending) and then can be written to by both sides. The fact that the side
which is able to write a zero into a semaphore subsequently locks out writes
from the other side is what makes semaphore flags useful in interprocessor
communications. (A thorough discussion on the use of this feature follows
shortly.) A zero written into the same location from the other side will be
stored in the semaphore request latch for that side until the semaphore is
freed by the first side.
that a flag that is a one reads as a one in all data bits and a flag containing
a zero reads as all zeros. The read value is latched into one side’s output
register when that side's semaphore select (SEM) and output enable (OE)
signals go active. This serves to disallow the semaphore from changing
state in the middle of a read cycle due to a write cycle from the other side.
Because of this latch, a repeated read of a semaphore in a test loop must
cause either signal (SEM or OE) to go inactive or the output will never
change.
to guarantee that no system level contention will occur. A processor
requests access to shared resources by attempting to write a zero into a
semaphore location. If the semaphore is already in use, the semaphore
request latch will contain a zero, yet the semaphore flag will appear as one,
a fact which the processor will verify by the subsequent read (see Table
VI). As an example, assume a processor writes a zero to the left port at
a free semaphore location. On a subsequent read, the processor will verify
that it has written successfully to that location and will assume control over
the resource in question. Meanwhile, if a processor on the right side
attempts to write a zero to the same semaphore flag it will fail, as will be
verified by the fact that a one will be read from that semaphore on the right
IDT7028L
High-Speed 64K x 16 Dual-Port Static RAM
The semaphore flags are active LOW. A token is requested by writing
The eight semaphore flags reside within the IDT7028 in a separate
When writing to a semaphore, only data pin D
When a semaphore flag is read, its value is spread into all data bits so
A sequence WRITE/READ must be used by the semaphore in order
0
– A
2
. When accessing the semaphores, none of
0
is used. If a LOW level
16
side during subsequent read. Had a sequence of READ/WRITE been
used instead, system contention problems could have occurred during the
gap between the read and write cycles.
by either repeated reads or by writing a one into the same location. The
reason for this is easily understood by looking at the simple logic diagram
of the semaphore flag in Figure 4. Two semaphore request latches feed
into a semaphore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag LOW and the other
side HIGH. This condition will continue until a one is written to the same
semaphore request latch. Should the other side’s semaphore request latch
have been written to a zero in the meantime, the semaphore flag will flip
over to the other side as soon as a one is written into the first side’s request
latch. The second side’s flag will now stay LOW until its semaphore request
latch is written to a one. From this it is easy to understand that, if a semaphore
is requested and the processor which requested it no longer needs the
resource, the entire system can hang up until a one is written into that
semaphore request latch.
single token by attempting to write a zero into it at the same time. The
semaphore logic is specially designed to resolve this problem. If simulta-
neous requests are made, the logic guarantees that only one side receives
the token. If one side is earlier than the other in making the request, the first
side to make the request will receive the token. If both requests arrive at
the same time, the assignment will be arbitrarily made to one port or the
other.
semaphores alone do not guarantee that access to a resource is secure.
As with any powerful programming technique, if semaphores are misused
or misinterpreted, a software error can easily happen.
via the initialization program at power-up. Since any semaphore request
flag which contains a zero must be reset to a one, all semaphores on both
sides should have a one written into them at initialization from both sides
to assure that they will be free when needed.
SEMAPHORE
WRITE
It is important to note that a failed semaphore request must be followed
L PORT
The critical case of semaphore timing is when both sides request a
One caution that should be noted when using semaphores is that
Initialization of the semaphores is not automatic and must be handled
REQUEST FLIP FLOP
D
0
READ
SEMAPHORE
D
Figure 4. IDT7028 Semaphore Logic
Industrial and Commercial Temperature Ranges
Q
REQUEST FLIP FLOP
SEMAPHORE
Q
D
SEMAPHORE
READ
R PORT
4836 drw 18
D
WRITE
0