stlvds31b STMicroelectronics, stlvds31b Datasheet
stlvds31b
Available stocks
Related parts for stlvds31b
stlvds31b Summary of contents
Page 1
... Pin compatible with the AM26LS31, SN65LVDS31 ■ Low voltage TTL (LVTTL) logic input levels Description The STLVDS31B is a quad differential line drivers that implements the electrical characteristics of low voltage differential signaling (LVDS). This signaling technique lowers the output voltage levels differential standard levels (such as ...
Page 2
Contents 1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Pin configuration Figure 1. Pin connections and functional diagram Table 2. Pin description Pin n° 10 11 Symbol Driver inputs 1Y to ...
Page 4
Figure 2. Logic diagram and logic symbol Table 3. Truth table for receiver ≥ 100 100 mV < V ≤ −100 OPEN Table 4. Truth table Input A H ...
Page 5
Maximum ratings Table 5. Absolute maximum ratings Symbol V Supply voltage input voltage I T Storage temperature range STG 1. All voltages except differential I/O bus voltage, are with respect to the network ground terminal. Note: ...
Page 6
Electrical characteristics Over recommended operating conditions unless otherwise noted. All typical values are °C, and Table 7. Electrical characteristics Symbol Parameter V Differential output voltage OD Change in differential output ΔV OD ...
Page 7
Over recommended operating conditions unless otherwise noted. All typical values are °C, and Table 8. Switching characteristics Symbol Parameter Propagation delay time, low to high t PLH output Propagation delay time, high to ...
Page 8
Typical characteristics 4 Figure 3. Voltage and current definitions Figure 4. Test circuit, timing and voltage definitions for differential output signal 1. All input pulse are supplied by a generator having the following characteristics: t repetition rate (PRR ...
Page 9
Figure 6. Enable and disable time test circuit and waveform 1. All input pulse are supplied by a generator having the following characteristics: t repetition rate (PRR) = 0.5 Mpps, pulse width = 500 ± includes ...
Page 10
Typical performance characteristics Unless otherwise specified T Figure 7. Supply current vs. temperature Figure 9. Propagation delay enable to output Figure 10. Propagation delay time Figure 11. Differential output signal 10/ °C J Figure 8. Supply current ...
Page 11
Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ...
Page 12
Dim. Min 0.05 A2 0.8 b 0.19 c 0.09 D 4.9 E 6 0° PIN 1 IDENTIFICATION 1 12/15 TSSOP16 mechanical data mm. Typ. Max. 1.2 0.15 1 ...
Page 13
Tape & reel TSSOP16 mechanical data mm. Dim. Min. Typ 12 6.7 Bo 5.3 Ko 1.6 Po 3.9 P 7.9 Max. Min. 330 13.2 0.504 0.795 2.362 22.4 6.9 0.264 5.5 0.209 ...
Page 14
Revision history Table 9. Document revision history Date Revision 28-Mar-2006 5 15-Jul-2009 6 14/15 Changes Order codes updated. Modified: Features on page 1. Doc ID 8338 Rev 6 ...
Page 15
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...