tda7052bt-n1 NXP Semiconductors, tda7052bt-n1 Datasheet

Page 1

DATA SHEET TDA7052B Mono BTL audio amplifier with DC volume control Product specification Supersedes data of 1966 May 28 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 1997 Aug 15 ...

Page 2

... SO8 plastic small outline package; 8 leads; body width 3.9 mm 1997 Aug 15 GENERAL DESCRIPTION The TDA7052B and TDA7052BT are 1 W and 0.5 W mono Bridge-Tied Load (BTL) output amplifiers with DC volume control. They have been designed for use in TV and monitors, but are also suitable for use in battery-fed portable recorders and radios ...

Page 3

... – i STABILIZER TEMPERATURE V ref PROTECTION Fig.1 Block diagram. DESCRIPTION handbook, halfpage 3 Product specification TDA7052B 5 positive output 8 negative output 3 6 MSA705 - 1 signal power ground ground OUT n.c. TDA7052B TDA7052BT GND1 3 6 GND2 OUT MSA704 - 1 Fig.2 Pin configuration. ...

Page 4

... Mono BTL audio amplifier with DC volume control FUNCTIONAL DESCRIPTION The TDA7052B and TDA7052BT are mono BTL output amplifiers with DC volume control which have been designed for use in TV and monitors but are also suitable for use in battery-fed portable recorders and radios. ...

Page 5

... Maximum gain ( output power O TDA7052B TDA7052BT THD total harmonic distortion TDA7052B TDA7052BT G maximum total voltage gain v(max) V input signal handling (RMS value noise output voltage (RMS value bandwidth SVRR supply voltage ripple rejection ...

Page 6

Philips Semiconductors Mono BTL audio amplifier with DC volume control 40 handbook, halfpage G v (dB 120 0 0.4 0.8 1.2 Fig.3 Gain control as a function of DC volume control. 25 handbook, halfpage ...

Page 7

Philips Semiconductors Mono BTL audio amplifier with DC volume control 10 handbook, halfpage THD (%) 8 ( ...

Page 8

Philips Semiconductors Mono BTL audio amplifier with DC volume control 20 handbook, halfpage SVRR (dB Measured with ...

Page 9

... This capacitor can be omitted if the 220 F electrolytic capacitor is connected close to pin 1. For single-end application the output peak current may not exceed 100 mA; at higher output currents the short circuit protection (MCL) will be activated. 1997 Aug TDA7052B TDA7052BT – i TEMPERATURE STABILIZER PROTECTION Fig ...

Page 10

Philips Semiconductors Mono BTL audio amplifier with DC volume control handbook, halfpage volume control Fig.14 Application with potentiometer as volume control; maximum gain = 34 dB. 1997 Aug 15 handbook, halfpage 4 MCD387 Fig.15 Application with ...

Page 11

Philips Semiconductors Mono BTL audio amplifier with DC volume control PACKAGE OUTLINES DIP8: plastic dual in-line package; 8 leads (300 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions ...

Page 12

Philips Semiconductors Mono BTL audio amplifier with DC volume control SO8: plastic small outline package; 8 leads; body width 3 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A ...

Page 13

Philips Semiconductors Mono BTL audio amplifier with DC volume control SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit ...

Page 14

Philips Semiconductors Mono BTL audio amplifier with DC volume control DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published ...

Page 15

Philips Semiconductors Mono BTL audio amplifier with DC volume control 1997 Aug 15 NOTES 15 Product specification TDA7052B ...

Page 16

Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, ...