lan9117 Standard Microsystems Corp., lan9117 Datasheet - Page 129

• Manufacturer Part Number: lan9117
• Description: Lan9117 High-performance Single-chip 10/100 Non-pci Ethernet Controller
• Manufacturer: Standard Microsystems Corp.

High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Chapter 7 Operational Characteristics
SMSC LAN9117
7.1
7.2
Supply Voltage (VDD_A, VDD_REF, VREG, VDD_IO)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XTAL1, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 7.1
Note 7.2
Note 7.3
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating
applicable section of this specification is not implied.
Supply Voltage (VDD_A, VDD_REF, VREG, VDD_IO) . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 10%
Ambient Operating Temperature in Still Air (T
**Proper operation of the LAN9117 is guaranteed only within the ranges specified in this section.
Absolute Maximum Ratings*
Operating Conditions**
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XTAL1, XTAL2, EXRES1.
This rating does not apply to the following pins: EXRES1.
Conditions**",
DATASHEET
Section 7.5, "DC Electrical
129
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
(Note
(Note
(Note
7.1) . . . . . . . . . . . . . . . .0V to +3.3V+10%
7.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
7.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Specifications", or any other
Revision 1.5 (07-11-08)
o
C to +150
o
o
C to +70
C to +70
o
o
o
C
C
C