tja1050 NXP Semiconductors, tja1050 Datasheet
tja1050
Available stocks
Related parts for tja1050
tja1050 Summary of contents
Page 1
... DATA SHEET TJA1050 High speed CAN transceiver Product specification Supersedes data of 2002 May 16 INTEGRATED CIRCUITS 2003 Oct 22 ...
Page 2
... Much lower electromagnetic emission due to optimal matching of the output signals CANH and CANL Improved behaviour in case of an unpowered node No standby mode. This makes the TJA1050 eminently suitable for use in nodes that are in a power-down situation in partially powered networks. 0 < V < 5. time limit CC 0 < ...
Page 3
... TIME-OUT TIMER RECEIVER REFERENCE TJA1050 VOLTAGE Fig.1 Block diagram. handbook, halfpage 3 Product specification TJA1050 CANH GND CANL 6 2 MGS374 GND TXD GND 2 7 CANH TJA1050T CANL ref RXD MGS375 Fig.2 Pin configuration. ...
Page 4
... Philips Semiconductors High speed CAN transceiver FUNCTIONAL DESCRIPTION The TJA1050 is the interface between the CAN protocol controller and the physical bus primarily intended for high-speed automotive applications using baud rates from 60 kbaud Mbaud. It provides differential transmit capability to the bus and differential receiver capability to the CAN protocol controller fully compatible to the “ ...
Page 5
... Product specification MIN. MAX. 0.3 +6 < 5. +40 < 5. + 200 +200 200 +200 4000 +4000 200 +200 55 +150 40 +150 is where R vj amb th(vj-a) VALUE 145 50 TJA1050 UNIT fixed th(vj-a) UNIT K/W K/W ...
Page 6
... TXD CC no load 6 Product specification MIN. TYP 2 2 0.3 +0 100 200 300 0.3 +0 8.5 20 0.45V 0.5V 0.55V CC CC 2.0 2.5 3.0 2.0 2.5 3.0 2.0 +2.5 2.0 +2.5 3.0 3.6 4.25 0.5 1.4 1.75 1.5 2.25 3 +50 TJA1050 MAX. UNIT 0 0 ...
Page 7
... V 100 CC CANH 100 CC CANL 155 250 TXD 7 Product specification TJA1050 TYP. MAX. UNIT 100 mA 0.7 0 100 7 7 ...
Page 8
... Fig.3 Application information. 100 TXD 1 nF CANH ref 5 TJA1050 1 nF CANL RXD GND Fig.4 Test circuit for automotive transients. 8 Product specification CANH 7 CAN BUS LINE CANL MGS380 TRANSIENT GENERATOR MGS379 TJA1050 ...
Page 9
... Oct 22 hysteresis 0.5 0.9 Fig.5 Hysteresis of the receiver 100 TXD CANH ref 5 TJA1050 CANL RXD GND Fig.6 Test circuit for timing characteristics. 9 Product specification MGS378 HIGH LOW V i(dif)(bus) ( 100 pF MGS376 TJA1050 ...
Page 10
... RXD 0. TXD-RXD ) Fig.7 Timing diagram for AC characteristics. 6.2 k CANL TJA1050 6.2 k CANH test PCB 10 HIGH LOW dominant (BUS on) 0.9 V 0.5 V recessive (BUS off) HIGH 0.7V CC LOW t d(TXD-BUSoff) t d(BUSoff-RXD TXD-RXD ) MGS377 10 nF ACTIVE PROBE SPECTRUM- ANALYZER GND MGT229 Product specification TJA1050 ...
Page 11
... Fig.9 Typical electromagnetic emission MHz (peak amplitude measurement). 80 handbook, full pagewidth A ( Data rate of 500 kbits/s. Fig.10 Typical electromagnetic emission MHz (peak amplitude measurement and envelope on peak amplitudes). 2003 Oct Product specification TJA1050 MGT231 (MHz) MGT233 (MHz) ...
Page 12
... RF voltage reached with no errors Data rate of 500 kbits/s. 2003 Oct 22 30 CANL 4.7 nF TJA1050 30 CANH TJA1050 test PCB MGT230 1 10 Fig.12 Typical electromagnetic immunity. 12 Product specification TJA1050 RF VOLTMETER AND POWER AMPLIFIER 50 RF SIGNAL GENERATOR GND MGT232 (MHz ...
Page 13
... Fig.13). 2003 Oct 22 (1) y handbook, halfpage 103 85 111 111 1094 1115 x 0 1115 0 1097 The backside of the bare die must be connected to ground. Fig.13 Bonding pad locations. 13 Product specification TJA1050 TJA1050U test pad MGS381 y ...
Page 14
... REFERENCES JEDEC JEITA MS-012 detail 1.0 0.7 1.05 0.25 0.25 0.4 0.6 0.039 0.028 0.041 0.01 0.01 0.016 0.024 EUROPEAN PROJECTION Product specification TJA1050 SOT96 ( 0.7 0.1 0 0.028 0.004 0.012 ISSUE DATE 99-12-27 03-02-18 ...
Page 15
... Use a low voltage ( 2.5 mm less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 15 Product specification TJA1050 ...
Page 16
... Added recommendation to connect unused pin S to ground Added Chapter REVISION HISTORY Product specification (9397 750 09778) 16 Product specification SOLDERING METHOD WAVE REFLOW not suitable suitable (4) not suitable suitable suitable suitable (5)(6) not recommended suitable (7) not recommended suitable not suitable not suitable DESCRIPTION TJA1050 (2) ...
Page 17
... Product specification TJA1050 DEFINITION These products are not Philips Semiconductors ...
Page 18
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2003 All rights are reserved. Reproduction in whole or in part is prohibited ...